1.0.1 This code is formulated with view to rational design of automatic fire alarm system, prevention and reduction of fire hazards and protection of the personal and property safety.
1.0.2 This code is applicable to design of automatic fire alarm system located in the constructed, renovated and extended building and structure but not applicable to that located at the places for production and storage of gunpowder, explosive, ammunition and explosive device.
1.0.3 Aimed at the features of the protected objects, the design of automatic fire alarm system shall comply with the relevant national guideline and policy and realize the safety and reliability, advanced technology and economic feasibility.
1.0.4 The design of automatic fire alarm system shall not only comply with this code but those in the current relevant standards of the nation.
Foreword I
1 General Provisions
2 Terms
3 Basic Requirement
3.1 General Requirements
3.2 Choice and Design of System
3.3 Division of the Alarm Zone and Detection Zone
3.4 Fire Control Center
4 Automatic Control Design
4.1 General Requirements
4.2 Automatic Control Design of the Automatic Sprinkler System
4.3 Automatic Control Design of Fire Hydrant System
4.4 Automatic Control Design of Gases (Bubble) Fire-extinguishing System
4.5 Automatic Control Design of Smoke Exhaust System
4.6 Automatic Control Design of Fire Door and Fire Roller Shutter System
4.7 Automatic Control Design of Elevator
4.8 Automatic Control Design of the Fire Alarm and Signalling Device
4.9 Automatic Control Design of the Fire Emergency Lighting System
4.10 Automatic Control Design of the Related Equipment
5 Fire Detector Choice
5.1 General Requirements
5.2 Choice of Point Type Fire Detector
5.3 Choice of Line type Fire Detector
5.4 Choice of Aspirating Smoke Detector
6 Setting of the Equipment
6.1 Setting of the Fire Alarm Control Unit and Automatic Control Equipment
6.2 Setting of the Fire Detector
6.3 Setting of the Manual Call Point
6.4 Setting of the Fire Display Panel
6.5 Setting of the Fire Alarm Singalling Device
6.6 Setting of the Sounder Equipment for Fire Emergency Purposes
6.7 Setting of the Fire Telephone
6.8 Setting of the Module
6.9 Setting of the Graph Indicator in Fire Control Center
6.10 Setting of the Routing Equipment
6.11 Setting of the Indicator and Control Unit for Fire Doors
7 Fire Alarm and Safety System Installed in Dwelling Building
7.1 General Requirement
7.2 System Design
7.3 Setting of the Fire Detector
7.4 Setting of the Fire Alarm Control Unit for Household
7.5 Setting of the Fire Alarm Signalling Device
7.6 Setting of the Emergency Broadcast Device
8 Combustible Gas Detection and Alarm System
8.1 General Requirement
8.2 Setting of the Combustible Gas Detector
8.3 Setting of the Combustible Gas Control Unit
9 Alarm and Monitoring System for Electric Fire Protection
9.1 General Requirement
9.2 Setting of the Leakage Current Detector for Electric Fire Prevention
9.3 Setting of the Heat Detector for Electric Fire Prevention
9.4 Setting of the Independent Detector for Electric Fire Prevention
9.5 Setting of the Alarm and Control Unit for Electric Fire Protection
10 Power Supply
10.1 General Requirement
10.2 Ground Connection
11 Wiring
11.1 General Requirement
11.2 Interior Wiring
12 Automatic Fire Alarm System for Typical Place
12.1 The Traffic Tunnel
12.2 The Oil Tank Area
12.3 The Cable Tunnel
12.4 The Large Space Places Where Higher than 12m
Appendix A Operating Status Information Table for Fire Alarm & the Fire Equipment in the Building
Appendix B Fire Safety Management Information Table
Appendix C Classification for the Point Type Heat Detectors
Appendix D Specific Setting of the Detectors
Appendix E Limit Curve for Install Space of the Detectors
Appendix F Setting of Detectors Influenced by Roof Beam
Appendix G Number of the Roof Beams Protected by One Detector Based on the Roof Beams Area
Explanation of Wording in This Code
List of Quoted Standards
