1 Scope
This standard specifies terms and definitions, requirements, test methods, inspection rules, installation, mark, label and package of the vehicle traveling data recorder.
This standard is applicable to the design, manufacturer, inspection and application of the vehicle travelling data recorder.
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendment) applies.
GB 2312 "Code of Chinese Graphic Character Set for Information Interchange--Primary Set"
GB/T 2423.1 "Environmental Testing for Electric and Electronic Products-Part 2: Test Methods-Tests A: Cold"
GB/T 2423.2 "Environmental Testing for Electric and Electronic Products-Part 2: Test Methods-Tests B: Dry Heat"
GB/T 2423.3 "Environmental Testing for Electric and Electronic Products-Part 2: Testing Method-Test Cab: Damp Heat Steady State"
GB/T 2423.5 "Environmental Testing for Electric and Electronic Products-Part 2: Test Methods-Test Ea and Guidance: Shock"
GB/T 2423.10 "Environmental Testing for Electric and Electronic Products-Part 2: Test Methods-Test Fc and Guidance: Vibration (Sinusoidal)"
GB 4094 "Motor Vehicles-Symbols for Controls, Indicators and Tell-tales"
GB 4208 "Degrees of Protection Provided by Enclosure (IP Code)"
GB/T 12534 "Motor Vehicles-General Rules of Road Test Method"
GB/T 16649.1 "Identification Cards--Integrated Circuit(s) Cards with Contacts--Part 1: Physical Characteristics"
GB/T 16649.2 "Identification Cards-Integrated Circuit(s) Cards with Contacts-Part 2: Dimensions and Location of the Contacts"
GB 16735-2004 "Road Vehicles-Vehicle Identification Number (VIN)"
GB/T 19951-2005 "The Safety Constructional Requirements for Double-deck Large Passenger Vehicles"
GB/T 21437.2-2008 "Road Vehicles--Electrical Disturbances from Conduction and Coupling--Part 2: Electrical Transient Conduction along Supply Lines Only"
GA 36 "License Plate of Motor Vehicle of the People's Republic of China"
JT/T 794-2011 "GNSS System for Operating Vehicles-Technical Specification for Vehicle Terminals"
Foreword I
Introduction III
1 Scope
2 Normative References
3 Terms and Definitions
4 Requirements
4.1 General Requirements
4.2 Electrical Components
4.3 Electrical Performances
4.4 Functional Requirements
4.5 Performance Requirements
4.6 Data Analysis Software
4.7 Data Security
4.8 Climatic Environment Adaptability
4.9 Mechanical Environment Adaptability
4.10 Enclosure Protection Degree
4.11 Anti-interference of Electric Ignition of Automobile
4.12 Electrostatic Discharge Immunity
4.13 Transient Immunity
5 Test Methods
5.1 Generally-required Checks
5.2 Check of Electrical Components
5.3 Electrical Performance Test
5.4 Function Check
5.5 Performance Test
5.6 Data Analysis Software Check
5.7 Data Security Check
5.8 Climatic Environment Adaptability Test
5.9 Mechanical Environment Test
5.10 Enclosure Protection Degree Test
5.11 Test for Anti-interference of Electric Ignition of Automobile
5.12 Test for Electrostatic Discharge Immunity
5.13 Test for Transient Immunity
6 Inspection Rules
6.1 Type Inspection
6.2 Delivery Inspection
7 Installation
7.1 New Vehicle
7.2 Vehicle in Service
7.3 Installation Position
7.4 Wiring Requirements
8 Marking, labeling and packaging
8.1 Marking and Labeling
8.2 Manufacture Certificate
8.3 Packaging
Appendix A (Normative) RS232 Serial Data Communication Protocol
Appendix B (Normative)Data Storage Format of USB (Universal Serial Bus)
Appendix C (Informative) Data Storage Format of Driver Identification IC Card
Appendix D (Informative) Curve of Accident Doubtful Point Data
Bibliography
