![]() |
中标分类
行业分类
ICS分类
最新标准
|
登录注册 |
您的位置: 标准明细 |
Air cleaner 1 Scope This document specifies the air cleaner in aspects of terms and definitions, classification and model designation, requirements, test conditions, test methods, inspection rules, and marking, instructions for use, packaging, transportation and storage. Note 1: The air cleaners involved in this document include independent ones and various air cleaning modules. This document is applicable to the air cleaners (hereinafter referred to as "cleaners") for household and similar uses with removal capacity for one or more of target pollutants such as particulate matters, gaseous pollutants, microorganisms (bacteria, fungi and viruses), odor and allergens. This document is applicable to, but not limited to, the cleaners in the following working principles: filter, adsorption, complex, chemical catalytic, photocatalytic, electrostatic, plasma, composite and other types. Note 2: The composite type refers to the cleaner designed in two or more cleaning principles that is able to remove one or more air pollutants. This document may be referenced for the following products: ——Small-sized cleaner, portable cleaner and cleaner for passenger car; ——Duct type cleaning device and other similar cleaners; ——Other products with air cleaning function. Note 3: For example, air conditioners, dehumidifiers, fresh air ventilators, fans, humidifiers, warm air blowers and vacuum cleaners. This document is not applicable to: ——Cleaners specially designed for industrial use; ——Cleaners used in the special environment and locations of corrosive and explosive gas (e.g. dust, vapor and gas); ——Cleaners specially designed for medical use. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 191 Packaging - Pictorial marking for handling of goods GB/T 1019 General requirements for the package of household and similar electrical appliances GB/T 2828.1 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection GB/T 2829 Sampling procedures and tables for periodic inspection by attributes (apply to inspection of process stability) GB/T 4214.1-2017 Test method for noise of household and similar electrical appliances - General requirements GB 4706.1 Household and similar electrical appliances - Safety - Part 1: General requirements GB 4706.45 Household and similar electrical appliances - Safety - Particular requirements for air-cleaning appliances GB/T 5296.2-2008 Instructions for use of products of consumer interest - Part 2: Household and similar electrical appliances GB/T 18883 Indoor air quality standard GB 19489 Laboratories - General requirements for biosafety GB 21551.3 Antibacterial and cleaning function for household and similar electrical appliances - Particular requirements of air cleaner GB/T 35758-2017 Household electrical appliances - Measurement of standby power QB/T 5364-2019 Requirement and evaluation method of test chamber for air cleaner 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 air cleaner electrical appliances for household and similar uses with certain capacity to remove one or more target pollutants from the indoor air 3.2 target pollutant specific air pollutants with well-defined composition, mainly including particulate matters, gaseous pollutants, microorganisms, allergens and odor Note 1: Particulate matters refer to solid, liquid or solid-liquid granular substances (e.g., dust, fume, mist, etc.) suspending in the air. Note 2: Gaseous pollutants refer to multi-component or single-component gaseous chemicals in the indoor air environment that are harmful to human beings or organisms. Note 3: Microorganisms refer to all tiny organisms that are difficult for individuals to observe with naked eyes. Note 4: Allergens refer to substances that cause an allergic reaction in human body. Note 5: Odor refers to the special smell that easily causes people's nausea, allergy and other discomfort reactions. 3.3 particulate matter PM2.5 particulate matter having an aerodynamic equivalent diameter of 2.5μm or less in the air [Source: GB 3095-2012, 3.4, modified] 3.4 test chamber device, with a limited confined space and the standard test conditions, for determining the capacity of a cleaner to remove target pollutants in the air 3.5 Working modes 3.5.1 rated mode(s) continuous and stable operation mode indicated on the cleaner, corresponding to its optimum cleaning capacity for the target pollutants 3.5.2 low noise mode(s) continuous and stable low-noise operation mode indicated on the cleaner, such as "night", "sleep", "silent" modes 3.5.3 auto mode(s) operation mode of the cleaner that it can realize auto adjustment of working gear by relying on sensors, algorithms, etc., without manual operation 3.5.4 off mode(s) any modes usually persisting where the energy using unit of the air cleaner is connected to a main power source and the cleaner is not running in standby mode, network mode or active mode function Note: An indicator that only shows the user that the cleaner is in the off position is included within the classification of the off mode. The guidance on modes and functions may be found in GB/T 35758-2017, Annex A. [Source: GB/T 35758-2017, 3.5, modified] 3.5.5 non-network standby mode(s) any modes usually persisting where the cleaner is connected to a mains power source without network connectivity and offers one or more of the following user oriented or protective functions ——to facilitate the activation of other modes (including activation or deactivation of active mode) by remote switch (including remote control), internal sensor, timer; ——information or status displays including clocks; ——sensor-based functions. Note: The guidance on modes and functions may be found in GB/T 35758-2017, Annex A. A timer is a continuous clock function (which may or may not be associated with a display) that provides regular scheduled tasks (e.g. switching) and that operates on a continuous basis. [Source: GB/T 35758-2017, 3.6, modified] 3.5.6 network standby mode(s) any modes where the cleaner is connected to a mains power source and at least one network function is activated (such as reactivation via network command or network integrity communication) but where the primary function is not active Note: Where a network function is provided but is not active and/or not connected to a network, then this mode will not function. A network function could become active intermittently according to a fixed schedule or in response to a network requirement. A "network" in this context includes communication between two or more separate independently powered devices or products. A network does not include one or more controls which are dedicated to a single product. Network mode may include one or more standby functions. [Source: GB/T 35758-2017, 3.7, modified] 3.6 standby power power consumed by a cleaner in off, standby and network modes Note: It is expressed in watts (W). 3.7 total decay reduction of concentration of the target pollutants in the air in a specified space under the specified conditions due to combined action of natural decay and cleaning operation Note: Natural decay refers to the reduction of concentration of the target pollutants in the air in a specified space under the specified conditions due to non-human factors such as settlement, agglomeration, surface deposition, chemical reaction and air exchange. 3.8 clean air delivery rate; CADR Q parameter of a cleaner’s cleaning capacity against the target pollutants (particulate matters and gaseous pollutants) under the specified test conditions, indicating the rate of the cleaner to provide clean air Note: It is expressed in cubic meters per hour (m3/h). 3.9 cumulate clean mass; CCM M parameter of a cleaner’s cumulate cleaning capacity against the target pollutants (particulate matters and gaseous pollutants) under the specified test conditions, indicating the total mass of target pollutants cleaned cumulatively by the cleaner until the cleaner’s measured CADR decays to 50% of the initial value Note: It is expressed in milligrams (mg). 3.10 cleaning energy efficiency η clean air delivery rate generated by the cleaner in the rated mode per unit power consumption Note: It is expressed in cubic meters per watt-hour [m3/(W·h)]. 4 Classification and model designation 4.1 Classification 4.1.1 Classification by cleaning principle Cleaners may be classified into several categories, including but not limited to: ——filter type; ——electrostatic type; ——catalytic type; ——plasma type; ——physical or chemical adsorption type; ——ozone type; ——composite type. 4.1.2 Classification by installation (use) method Cleaners may be classified into: ——ground type; ——table type; ——wall-mounted type; ——plug-in type; ——ceiling type; ——on board type; ——robot type; ——duct type; ——wearable type. Foreword III 1 Scope 2 Normative references 3 Terms and definitions 4 Classification and model designation 5 Requirements 5.1 Particulate matter cleaning 5.2 Gaseous pollutant cleaning 5.3 Microorganism removal 5.4 Standby power 5.5 Noise 5.6 Cleaning energy efficiency 5.7 Other performance 6 Test conditions 6.1 General conditions 6.2 Measuring instruments 6.3 Test chamber 6.4 Sample machine to be tested 6.5 Target pollutants 7 Test methods 7.1 Particulate matter cleaning 7.2 Gaseous pollutant cleaning 7.3 Microorganism removal 7.4 Standby power 7.5 Noise 7.6 Cleaning energy efficiency 7.7 Other performance 8 Inspection rules 8.1 Inspection classification 8.2 End-of-manufacturing inspection 8.3 Type inspection 8.4 Treatment of inspection samples 9 Marking, instructions for use, packaging, transportation and storage 9.1 Marking 9.2 Instructions for use 9.3 Packaging 9.4 Transportation and storage Annex A (Nominative) Test method for the clean air delivery rate for particulate matters Annex B (Informative) Calculation method of effective room size Annex C (Nominative) Test method for cumulate clean mass of particulate matters Annex D (Informative) Conversion method of particulate matter cleaning life span Annex E (Nominative) Test method of clean air delivery rate for gaseous pollutants Annex F (Normative) Test method for cumulate clean mass of gaseous pollutants Annex G (Informative) Conversion method of cleaning life span for gaseous pollutants Annex H (Normative) Test method for removal capacity for virus Annex I (Informative) Test method for allergen removal capacity Annex J (Informative) Test method for odor removal performance Annex K (Informative) Test method for cleaning performance in auto mode Annex L (Informative) Test method for performance of duct type cleaning device Annex M (Informative) Test method for performance of wearable cleaner Annex N (Informative) Test method for secondary odor simulation Annex O (Informative) Dynamic equilibrium test method (ozone removal) Bibliography 空气净化器 1 范围 本文件规定了空气净化器的术语和定义、分类与型号命名、要求,试验条件、试验方法、检验规则、标志、使用说明,包装、运输及贮存。 注1:本文件涉及的空气净化器包含独立的空气净化器具及各类空气净化模块。 本文件适用于对颗粒物、气态污染物、微生物(细菌、真菌、病毒等)、异味和过敏原等上述一种或多种目标污染物具有去除功能的家用和类似用途的空气净化器(以下简称“净化器”)。 本文件适用于但不限于下述工作原理的净化器:过滤式,吸附式,络合式,化学催化式、光催化式、静电式、等离子式、复合式等。 注2:复合式净化器指采用两种或两种以上净化原理,可去除一种或一种以上空气污染物的净化器。 下列产品可参考本文件执行: ——小型、便携式净化器,乘用车净化器; ——风道式净化装置及其他类似的净化器; ——带有空气净化功能的其他产品。 注3:例如,空调器、除湿机﹑新风机、风扇、加湿器、暖风机和吸尘器等。 本文件不适用于: ——专为工业用途而设计的净化器; ——在腐蚀性和爆炸性气体(如粉尘、蒸气和瓦斯气体)特殊环境场所使用的净化器; ——专为医疗用途设计的净化器。 2 规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中,注日期的引用文件,仅该日期对应的版本适用于本文件;不注日期的引用文件,其最新版本(包括所有的修改单)适用于本文件。 GB/T 191 包装储运图示标志 GB/T 1019 家用和类似用途电器包装通则 GB/T 2828.1 计数抽样检验程序 第1部分:按接收质量限(AQL)检索的逐批检验抽样计划 GB/T 2829 周期检验计数抽样程序及表(适用于对过程稳定性的检验) GB/T 4214.1-2017 家用和类似用途电器噪声测试方法 通用要求 GB 4706.1 家用和类似用途电器的安全 第1部分:通用要求 GB 4706.45 家用和类似用途电器的安全 空气净化器的特殊要求 GB/T 5296.2-2008 消费品使用说明 第2部分:家用和类似用途电器 GB/T 18883 室内空气质量标准 GB 19489 实验室 生物安全通用要求 GB 21551.3 家用和类似用途电器的抗菌、除菌、净化功能 空气净化器的特殊要求 GB/T 35758-2017 家用电器 待机功率测量方法 QB/T 5364-2019 空气净化器测试用试验舱技术要求和评价方法 3 术语和定义 下列术语和定义适用于本文件。 3.1 空气净化器 air cleaner 对室内空气中一种或多种目标污染物具有一定去除能力的家用和类似用途电器。 3.2 目标污染物 target pollutant 成分构成明确的特定空气污染物,主要包括颗粒物、气态污染物,微生物,过敏原和异味等。 注1:颗粒物指悬浮在空气中的固态,液态或固态和液态的颗粒物状物质(如粉尘,烟、雾等)。 注2:气态污染物指室内空气环境中对人类或生物有害的多组分或单一成分的气态化学物质。 注3:微生物指个体难以用肉眼观察的一切微小生物的统称。 注4:过敏原指能够引发人体产生过敏反应的物质。 注5:异味指具有易引起人们恶心和过敏等不适反应的特殊气味。 3.3 细颗粒物 particulate matter PM2.5 环境空气中空气动力学当量直径小于或等于2.5 μm的颗粒物。 [来源:GB 3095-2012,3.4,有修改] 3.4 试验舱 test chamber 用于测定净化器对空气中目标污染物去除能力的限定密闭空间及标准试验条件的装置。 3.5 工作模式 3.5.1 额定模式 rated mode(s) 净化器明示的针对目标污染物的最佳净化能力,且持续稳定的运行模式。 3.5.2 低噪声模式 low noise mode(s) 净化器明示的“夜间”“睡眠”“静音”等低噪声运行且持续稳定运行的模式。 3.5.3 自动模式 auto mode(s) 在无人为操作下,依靠传感器、算法等实现自动调节运行挡位的运行模式。 3.5.4 关机模式 off mode(s) 净化器的供电装置连接到主电源时,未出现待机模式,网络模式或活跃模式,且状态持续的任何模式。 注:仅提示用户净化器是在关机位置的指示器,包括在关机模式的类别中。模式和功能指导见GB/T 35758-2017附录A。 [来源:GB/T 35758-2017,3.5,有修改] 3.5.5 非网络待机模式 non-network standby mode(s) 净化器连接到主电源时,无网络连通功能,提供以下一种或多种面向用户功能或保护功能,且为持续的任何模式。 ——可以通过触发远程开关(包括远程控制),内部传感器,定时器来触发其他模式(包括活跃模式开启或停止); ——信息或包含时钟的状态显示; ——基于传感器功能。 注:模式和功能指导见GB/T 35758-2017附录A。定时器是一个能执行定期的预定任务(比如开关),并且能持续工作的一种时钟功能(它可以带或者不带显示器)。 [来源:GB/T 35758-2017,3.6,有修改] 3.5.6 网络待机模式 network standby mode(s) 净化器在连接到主电源并且至少有一种网络功能已经开启(例如通过网络命令或者完整的网络通信来重新启动),但是主要功能尚未启动的模式。 注:网络功能如果没有启动和/或没有连接到网络,这种模式就不能应用。网络功能可被预先设定的指令集或网络请求响应所触发。“网络”在本文件中的含义包括了两台或更多台相互独立供电设备或产品之间的通信。网络不包含用于单个产品的一种或多种控制。网络模式可能包含一种或多种待机功能。 [来源:GB/T 35758-2017,3.7,有修改] 3.6 待机功率 standby power 净化器在关机、待机、网络模式下对应消耗的功率。 注:单位为瓦(W)。 3.7 总衰减 total decay 在规定空间及条件下,由于自然衰减和净化运行的共同作用,致使空气中目标污染物浓度的降低。 注:自然衰减指在规定空间及条件下,由于沉降、附聚,表面沉积,化学反应和空气交换等非人为因素,致使空气中目标污染物浓度的降低。 3.8 洁净空气量 clean air delivery rate;CADR Q 净化器在规定的试验条件下,针对目标污染物(颗粒物和气态污染物)净化能力的参数,表示净化器提供洁净空气的速率。 注:单位为立方米每小时(m3/h)。 3.9 累积净化量 cumulate clean mass;CCM M 净化器在规定的试验条件下,针对目标污染物(颗粒物和气态污染物)累积净化能力的参数,表示净化器的洁净空气量实测值衰减至初始值50%时,累积净化处理的目标污染物总质量。 注:单位为毫克(mg)。 3.10 净化能效 cleaning energy efficiency η 净化器在额定模式下单位功耗所产生的洁净空气量。 注:单位为立方米每瓦时[m3/(W·h)]。 4 分类与型号命名 4.1 分类 4.1.1 根据净化原理分类 净化器可以分为但不限于以下几类: ——过滤式; ——静电式; ——催化式; ——等离子式; ——物理或化学吸附式; ——臭氧式; ——复合式。 4.1.2 根据安装(使用)方式分类 净化器可以分为以下几类: ——落地式; ——桌面式; ——壁挂式; ——直插式; ——吸顶式; ——车载式; ——机器人式; ——管道型; ——可穿戴式。 4.2 命名方式 4.2.1 净化器应符合下述命名方式: 系列代号:以英文字母A~Z和阿拉伯数字01~99的任意组合表示 净化原理:净化原理分为以下几种主要类型: G——过滤式、D——静电式、F——复合式、Q——其他形式 净化器参数:洁净空气量,单位为立方米每小时(m3/h) 名称代号:空气净化器的两个汉字拼音字头 净化器命名示例:KJ600G-A01 其中: KJ——空气净化器; 600——洁净空气量为600 m3/h; G——过滤式; A01——表示A系列,第1款。 4.2.2 产品型号命名以产品的主功能参数为主。具有去除多种目标污染物能力的产品需要符合第9章的规定。 5 要求 5.1 颗粒物净化 5.1.1 洁净空气量 颗粒物洁净空气量实测值不应低于标称值的90%。 5.1.2 累积净化量 累积净化量与标称的洁净空气量应符合5.1.3的关联要求。 如标称了累积净化量的具体数值,且高于表1关联指标值,则实测值不应低于其标称值的90%。 5.1.3 关联指标 净化器对颗粒物的累积净化量与标称洁净空气量的关联性应符合表1要求。 表1 颗粒物净化的关联指标 洁净空气量(标称值)Q m3/h 累积净化量M mg 注:洁净空气量小于60 m3/h净化器,不做累积净化量评价。 5.2 气态污染物净化 5.2.1 洁净空气量 对标称的单成分或混合成分气态污染物的洁净空气量,实测值不应低于标称值的90%。 5.2.2 累积净化量 单成分加载下,对甲醛气体的累积净化量与标称的洁净空气量应符合5.2.3的关联要求。 如标称了高于表2关联指标值的单成分(或混合成分加载下单一目标污染物)累积净化量的具体数值,则实测值不应低于其标称值的80%。 5.2.3 关联指标 净化器单成分加载下,甲醛的累积净化量与标称洁净空气量的关联性应符合表2要求。 表2 甲醛净化的关联指标 洁净空气量(标称值)Q m3/h 累积净化量M mg 注:洁净空气量小于40 m3/h净化器,不做累积净化量评价。 5.3 微生物去除 5.3.1 抗菌除菌性能 如果净化器明示具有抗菌除菌功能,则应符合GB 21551.3的要求。 5.3.2 对病毒的去除性能 5.3.2.1 去除率要求 如果净化器明示具有除病毒功能,则在规定条件下的病毒去除率不应低于99.9%。 5.3.2.2 移舱检出限 5.3.2.1试验后进行规定的移舱检出限测试,应未检出。 5.4 待机功率 净化器在关机模式下的待机功率实测值不应大于0.5 W。 净化器在非网络待机模式下的待机功率最大实测值不应大于1.5 W。 净化器在网络待机模式下的待机功率最大实测值不应大于2.0 W。 有信息显示装置的净化器规定值增加0.5 W。 注:待机功率需注明工作模式。 5.5 噪声 5.5.1 净化器在额定模式下的洁净空气量实测值与对应的噪声值,应符合表3的规定。 净化器噪声实测值与标称值的允差不大于+3 dB(A)。 表3 洁净空气量与噪声对应关系 洁净空气量(实测值)Q m3/h 声功率级dB(A) 注:如果净化器可去除一种以上目标污染物,则按最大洁净空气量值确定表中对应的噪声限值。 5.5.2 若净化器明示具有“低噪声模式”,则在该模式下的最大声功率级工作噪声标称值不应高于38 dB(A),且实测值与标称值的允差不应大于+3 dB(A)。 净化器应标注或说明在“低噪声模式”下的最大净化性能。 5.6 净化能效 5.6.1 颗粒物净化能效 净化器对颗粒物净化能效值应不低于4.00 m3/(W·h),且实测值不应小于其标称值的90%。 5.6.2 气态污染物净化能效 净化器对气态污染物(单成分)净化能效值应不低于1.00 m3/(W·h),且实测值不应小于其标称值的90%。 5.7 其他性能 本文件对于净化器明示的其他功能,以及特殊类型的空气净化器产品的净化能力给出了对应的试验方法和评价建议,参见7.7。 6 试验条件 6.1 一般条件 试验应符合下述一般条件: a) 除对试验环境条件另做具体规定的试验外,型式试验应在环境温度为(23±3)℃,相对湿度为(50±10)%,无外界气流,无强烈阳光和其他辐射作用的室内进行; b) 试验电源为单相交流正弦波,电压和频率的波动范围不应超过额定值的±1%; c) 被测样机应在额定模式或其他需要进行测试的模式下,按照使用说明规定的使用方法进行试验; d) 试验前检查目标污染物发生,测量和记录等设备,均应处于正常使用状态。 6.2 测量仪器 6.2.1 通用测量仪器 试验通用测量仪器应满足下述要求: a) 用于型式试验的电工测量仪表,除已具体规定的仪表外,其精度应不低于0.5级,出厂试验应不低于1.0级; b) 温度计:最大允许误差±0.5℃; c) 湿度计:相对湿度最大允许误差±2%; d) 计时仪表:最大允许误差±l s/24 h。 6.2.2 专用测量仪器 针对不同的试验内容,专用测量仪器应符合相应附录的要求。 6.3 试验舱 如无特殊规定,试验舱应符合QB/T 5364-2019规定的3 m3,10 m3,30 m+和 81 m3试验舱要求。 6.4 待测样机 6.4.1 工作模式设定 除另有规定,应在净化器的额定模式下进行试验;若净化器无额定模式,则默认开启最高挡位进行测试。 注:对于净化功能是辅助功能的产品,如空调器、除湿机和新风机等,则试验时只需要按照使用说明书启动其净化功能额定模式或开启最高挡位进行测试。 6.4.2 放置位置 试验样机的放置应符合下述要求。 a) 3 m3试验舱 出风口高度小于400 mm的,应置于400 mm高的台面上,出风口高度大于或等于400 mm的,应放置在地面上。 b) 10 m3,30 m3,81 m3试验舱 中心位置:落地式(地上),桌面式(700 mm 的台面上),壁挂式(下沿距地面1 800 mm)。 上述规定外的其他机型,如无注明,按出风口高度分:出风口高度小于700 mm时,净化器放台面上进行试验;出风口高度大于或等于700 mm时,净化器放置在地面上进行试验。 6.5 目标污染物 针对不同的试验,目标污染物应符合相应的要求,详见各项对应的试验。 7 试验方法 7.1 颗粒物净化 7.1.1 洁净空气量 颗粒物洁净空气量的试验方法按附录A进行。 注:洁净空气量对应适用面积计算方法见附录B。 7.1.2 累积净化量 颗粒物累积净化量的试验方法按附录C进行。 注:颗粒物净化寿命换算方法见附录D。 7.2 气态污染物净化 7.2.1 洁净空气量 气态污染物洁净空气量(单成分和混合成分)试验方法按附录E进行。 7.2.2 累积净化量 气态污染物单成分和混合成分累积净化量试验方法按附录F进行。 注:气态污染物净化寿命换算方法见附录G。 7.3 微生物去除 7.3.1 抗菌除菌性能 净化器的抗菌除菌性能按照GB 21551.3中规定的方法进行。 7.3.2 对病毒的去除性能 净化器对病毒去除性能试验方法按附录H进行。 7.4 待机功率 7.4.1 根据3.5工作模式相关定义,判定净化器是否存在关机模式、非网络待机模式,网络待机模式。 7.4.2 待机功率试验按照GB/T 35758-2017规定的方法测试。 7.5 噪声 净化器在对应的工作模式下运行,按照GB/T 4214.1-2017的相关要求进行试验,并增加以下内容。 ——GB/T 4214.1-2017中6.5.4增加:壁挂式净化器,包括其附件,应安放在固定架上。安装时净化器距离地面0.6 m,其背面和垂直壁面之间的距离为D=(1±0.5)cm; ——对于基准体任一边长大于 0.7 m、自由放置的落地式净化器,包括嵌入式净化器,采用GB/T 4214.1-2017中 7.1.1的测试方法。 7.6 净化能效 7.6.1 输入功率 连接净化器与电参数测试仪表,接通电源,仪表进入测量状态;净化器在额定模式下稳定运行至少30 min后,开始读取测量值。 在开始读取测量值之后的30 min 内,测量的功率变化小于1%,可以直接读取测量值作为额定功率。 如果在此期间内测量的功率变化不小于1%,则应再延续测量至60 min,用此期间的耗电量积分值除以测试时间来计算平均功率,即为输入功率。 7.6.2 净化能效计算 净化器的净化能效按式(1)计算: (1) 式中: η——净化能效,单位为立方米每瓦时[m3/(W·h)]; Q——洁净空气量实测值,单位为立方米每小时(m3/h); P——输入功率实测值,单位为瓦(W)。 注:净化器若具有可分离的其他功能,则净化能效计算时的输入功率P,只考虑在实现净化功能时所消耗的功率值总和。 7.7 其他性能 7.7.1 过敏原去除性能 净化器对过敏原的去除性能试验方法及评价要求见附录I。 7.7.2 除异味性能 净化器除异味性能的试验方法及评价要求见附录J。 7.7.3 自动模式净化性能 净化器自动模式净化性能试验方法及评价要求见附录K。 7.7.4 风道式净化装置的净化性能 安装在风道内的风道式净化装置性能试验方法及评价要求见附录L。 7.7.5 可穿戴式净化器性能 可穿戴式净化器性能试验方法及评价要求见附录M。 7.7.6 模拟二次异味 净化器模拟二次异味试验方法及评价要求见附录N。 7.7.7 动态平衡试验(除臭氧性能) 动态平衡试验方法及评价要求见附录O。 8 检验规则 8.1 检验分类 净化器的检验分为出厂检验和型式检验。 8.2 出厂检验 8.2.1 出厂检验的必检项目 凡正式提出交货的净化器,均应进行出厂检验。 出厂检验的必检项目为表4的序号l~序号3。 8.2.2 出厂检验的抽查项目 净化器出厂时的抽样检验按GB/T 2828.1进行。检验批量﹑抽样方案、检查水平及合格质量水平,由生产厂和订货方共同商定。 抽样检验的项目见表4序号4、6、8、10、11。 表4 出厂检验和型式检验 序号 检验项目 不合格分类 要求 试验方法 1 标志 A 9.1 视检 2 电气强度 A GB 4706.45相关内容 GB 4706.45相关内容 3 接地电阻 A GB 4706.45相关内容 GB 4706.45相关内容 4 颗粒物洁净空气量 A 5.1.1 7.1.1 5 颗粒物累积净化量 B 5.1.2 7.1.2 6 气态污染物洁净空气量 A 5.2.1 7.2.1 7 气态污染物累积净化量 B 5.2.2 7.2.2 8 微生物去除(如果净化器明示具备该功能) A 5.3 7.3 9 待机功率 B 5.4 7.4 10 噪声 A 5.5 7.5 11 净化能效 B 5.6 7.6 8.3 型式检验 8.3.1 净化器在下列情况之一时,应进行型式检验: a) 经鉴定定型后制造的第1批产品或转厂生产的老产品; b) 正式生产后,当结构、工艺和材料有较大改变可能影响产品性能时; c) 产品停产一年后再次生产; d) 国家质量监督机构提出进行型式检验要求。 8.3.2 型式检验应包括本文件和GB 4706.45中规定的所有检验项目。 8.3.3 型式检验抽样应按GB/T 2829进行,检验用的样本应从出厂检验合格批中抽取2台,累积净化量试验另抽1台,共计3台。按每百台单位产品不合格品数计算,采用判别水平Ⅰ的1次抽样方案。不合格分类、不合格质量水平判定和判定数组见表5。 表5 产品不合格分类、不合格质量水平判定 不合格分类 A B C 不合格质量水平 30 65 100 判定数组 Ac 0 1 2 Re 1 2 3 8.4 检验样品处理 经出厂检验合格后,净化器方可作为合格产品交付订货方;经型式检验的样品一律不能作为合格产品使用。 9 标志,使用说明、包装、运输及贮存 9.1 标志 9.1.1 通用性标志 净化器的通用性标志应符合GB 4706.1,GB 4706.45和GB/T 5296.2-2008中 5.1的要求,此外,还应在产品上标注产品维护及滤网/滤材更换/清洗的文字提示。 9.1.2 性能指标 净化器的基础性能相关的标志内容包含以下几个方面。 a) 明示的去除目标污染物种类: 1) 颗粒物; 2) 气态污染物(单成分、混合成分); 3) 微生物(试验菌种或病毒); 4) 其他污染物。 b) 洁净空气量(CADR),应注明对应的目标污染物和试验条件。 注:目标污染物示例:甲醛、甲苯、苯乙烯等;试验条件示例:单成分加载,混合成分加载等。 c) 颗粒物累积净化量。 d) 气态污染物累积净化量(选标),注明对应的目标污染物及试验条件(单成分、混合成分)。 e) 噪声。 f) 低噪声模式(如有)。 g) 去除微生物及其他功能(如有)。 h) 耗材更换提示。 i) 如果应用于病原微生物污染环境,应有必要的提示和警示标志。 j) 其他工作模式及说明。 9.2 使用说明 净化器使用说明应符合GB/T 5296.2-2008的要求,除9.1规定的内容外,至少还应包括: a) 净化器的名称、型号及其他性能指标等; b) 安装和使用要求,维护和保养注意事项; c) 随机附件名称; d) 常见故障及处理办法一览表,售后服务事项; e) 制造厂名和地址; f) 净化器或净化器使用说明上还应具有以下注意事项及内容: ——安全注意事项; ——具体净化原理; ——放置场所的注意事项; ——使用时的注意事项; 注1:“使用时的注意事项”包括净化器使用过程中可能产生的负面影响等。 ——净化部件更换、清洗时的注意事项; ——其他的注意事项。 注2:“其他的注意事项”,例如,在有病原微生物污染环境下连续使用的净化器史换滤网时,对必要的防护措施做出提示。 9.3 包装 净化器的包装应符合GB/T 191和GB/T 1019的有关规定。 净化器应附有合格证和产品使用说明。 9.4 运输及贮存 净化器在运输过程中不应碰撞、挤压、抛扔和强烈的振动以及雨淋、受潮和曝晒。 净化器应贮存于干燥,通风、无腐蚀性及无爆炸性气体的库房内,并防止磕碰。 附录A (规范性) 颗粒物洁净空气量试验方法 A.1 试验原理 本试验原理依据“衰减法”:在一个相对密闭的空间里,颗粒物在空气净化器的作用下,浓度随净化作用时间遵循指数衰减的规律。可通过对试验中测试时间与对应浓度进行函数拟合,计算得出洁净空气量。 A.2 试验条件 A.2.1 专用测量仪器 激光尘埃粒子计数器,应满足以下要求: ——测试粒径范围应包括0.3 μm~10 μm; ——仪器量程应满足106 L-1(如果量程达不到,应配置合适的稀释器;或采用经过计量校准的同类等级的仪器)。 A.2.2 标准目标污染物 |
联系我们
|
微信联系客服
![]() |
关于我们 | 联系我们 | 收费付款 |
服务热线:400-001-5431 | 电话:010-8572 5110 | 传真:010-8581 9515 | Email: bz@bzfyw.com | |
版权所有: 北京悦尔信息技术有限公司 2008-2020 京ICP备17065875号-1 51La |
本页关键词: |
GB/T 18801-2022, GB 18801-2022, GBT 18801-2022, GB/T18801-2022, GB/T 18801, GB/T18801, GB18801-2022, GB 18801, GB18801, GBT18801-2022, GBT 18801, GBT18801 |