标准编号:	GB/T 9124.1-2019
中文名称:	钢制管法兰 第1部分：PN 系列
英文名称:	Steel pipe flanges—Part 1:PN designated
中标分类:	J15    管路附件
行业分类:	GB    国家标准
ICS分类:	23.040.60 23.040.60    法兰、管接头及其连接件 23.040.60
发布机构:	国家市场监督管理总局 国家标准化管理委员会
发布日期:	2019-05-10
实施日期:	2019-12-1
标准状态:	valid
替代旧标准:	GB/T 9112-2010 钢制管法兰　类型与参数 GB/T 9113-2010 整体钢制管法兰 GB/T 9114-2010 带颈螺纹钢制管法兰 GB/T 9115-2010 对焊钢制管法兰 GB/T 9116-2010 带颈平焊钢制管法兰 GB/T 9117-2010 带颈承插焊钢制管法兰 GB/T 9118-2010 对焊环带颈松套钢制管法兰 GB/T 9119-2010 板式平焊钢制管法兰 GB/T 9120-2010 对焊环板式松套钢制管法兰 GB/T 9121-2010 平焊环板式松套钢制管法兰 GB/T 9122-2010 翻边环板式松套钢制管法兰 GB/T 9123-2010 钢制管法兰盖 GB/T 9124-2010 钢制管法兰　技术条件
翻译语言:	英文
文件格式:	PDF
中文字符数:	153000 字
翻译价格(元):	5600.0
交付时间:	付款后 1 个工作日

Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative. GB/T 9124 consists of the following two parts under the general title Steel pipe flanges: ——Part 1: PN designed; ——Part 2: Class designated. This is Part 1 of GB/T 9124. This part is developed in accordance with the rules given in GB/T 1.1-2009. This part replaces the contents of PN designed flanges specified in GB/T 9112-2010 Types and parameters for steel pipe flanges, GB/T 9113-2010 Integral steel pipe flanges, GB/T 9114-2010 Hubbed screwed steel pipe flanges, GB/T 9115-2010 Butt-welding steel pipe flange, GB/T 9116-2010 Hubbed slip-on-welding steel pipe flanges, GB/T 9117-2010 Hubbed socket welding steel pipe flanges, GB/T 9118-2010 Loose hubbed steel pipe flanges with welding neck collar, GB/T 9119-2010 Slip-on-welding plate steel pipe flanges, GB/T 9120-2010 Loose plate steel pipe flanges with weld-neck collar and with weld ring neck, GB/T 9121-2010 Loose plate steel pipe flanges with weld-on collar, GB/T 9122-2010 Loose plate steel pipe flanges with lapped pipe end and pressed collar with long neck, GB/T 9123-2010 Steel pipe blank flanges and GB/T 9124-2010 Specification for steel pipe flanges; those of Class designated are incorporated in GB/T 9124, Part 2; the following main changes have been made with respect to GB/T 9112~9124-2010 series: ——the contents of PN designated flanges in Edition 2010 are supplemented and revised; ——the nominal pressure range of blind flange is extended from PN2.5~PN160 to PN2.5~PN400; ——the nominal size range of hubbed screwed flanges is changed from DN10~DN1000 to DN10~DN150; ——the outside diameter of steel pipe is revised, and the flange size is revised accordingly; ——some materials for flanges and their pressure-temperature ratings are supplemented; ——other relevant contents such as technical requirements are revised and improved; ——the method for determining the pressure-temperature rating is added. This part is redrafted by reference to but is not equivalent to ISO 7005-1: 2011 Pipe flanges - Part 1: Steel flanges for industrial and general service piping systems. This part was proposed by China Machinery Industry Federation. This part is under the jurisdiction of National Technical Committee on Pipelines and Accessories of Standardization Administration of China (SAC/T C237). The previous editions of this part are as follows: ——GB/T 9112~9124-1988, GB/T 9112~9124-2000, GB/T 9112~9124-2010.   Introduction GB/T 9112~9124-2010 series are mainly divided into 13 standards according to different flange types and are integrated into 2 standards after revision according to nominal pressure series of flanges, i.e., GB/T 9124.1-2019 Steel pipe flanges - Part 1: PN designated and GB/T 9124.2-2019 Steel pipe flanges - Part 2: Class designated. ISO 7005-1: 2011 Pipe flanges - Part 1: Steel flanges for industrial and general service piping systems specifies the technical contents of steel pipe flanges such as terms and definitions, purchaser specification data, process, pressure limits, material, application considerations, other considerations for specification, installation guidance and information to be specified by the purchaser; compared with ISO 7005-1: 1992, ISO 7005-1: 2011 no longer specifies detailed technical parameters, but requires direct reference to CEN standard EN 1092-1 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges, and ASMEB 16.5 Pipe flanges and flanged fittings NPS 1/2 through NPS 24 metric/inch standard and ASMEB 16.47 Large diameter steel flanges NPS 26 through NPS 60 metric/inch standard. The flange sizes specified in this part are interchangeable with those in EN 1092-1: 2018, with basically same technical requirements. The following main changes have been made with respect to EN 1092-1: 2018: ——the writing format of this part is different from EN 1092-1: 2018; ——according to the requirements of users in China, the flange nominal size range is appropriately extended, for example, the flange sizes of DN20 and DN32 with nominal pressure range of PN160~PN400 are added; ——according to the requirements of users in China, the types and sizes of flanges with ring joint faces are added; ——the types and sizes of hubbed socket welding flanges are supplemented; ——EN 1092-1: 2018 includes only one outside diameter series of steel pipe, while this part includes two outside diameter series of steel pipe; wherein, DN10~DN2400 steel pipes in Series I are basically the same as but DN65 and DN125 are different from those in EN 1092-1: 2018, DN2600~DN4000 steel pipes in Series II are the same as those in EN 1092-1: 2018; ——the flange material is different from that in EN 1092-1: 2018. The flange materials with Chinese designations are adopted in this part, of which, the pressure-temperature ratings are determined by reference to EN 1092-1: 2018; ——the order contract data of flanges are added; ——the pipe schedule number and steel pipe wall thickness are added; ——the corresponding relationship between this part and EN 1092-1 in terms of code for flange type and code for sealing face is added. Steel pipe flanges - Part 1: PN designated 1 Scope This part of GB/T 9124 specifies the styles and parameters, types and sizes, technical requirements, test, inspection and acceptance, signs and designations, and supply requirements of PN designated steel pipe flanges and blind flanges. This part is applicable to steel pipe flanges and blind flanges with nominal pressure of PN2.5~PN400 and nominal size of DN10~DN4000. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. GB/T 152.4 Fasteners - Counterbores for hexagon bolts and nuts GB/T 700 Carbon structural steels GB/T 711 Hot-rolled quality carbon structural steel plates and wide strips GB/T 712 Ship and ocean engineering structural steel GB/T 713 Steel plates for boilers and pressure vessels GB/T 1047 Pipework components - Definition and selection of nominal size GB/T 1048 Pipework components - Definition and selection of nominal pressure GB/T 1804 General tolerances - Tolerances for linear and angular dimensions without individual tolerance indications GB/T 3531 Low alloy steel plates for low temperature pressure vessels GB/T 4237 Hot rolled stainless steel plate, sheet and strip GB/T 7306.1 Pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads - Part 1: Parallel internal and taper external threads GB/T 9125 Fasteners for steel pipe flange joints GB/T 12228 General purpose industrial valves - Specification of carbon steel forgings GB/T 12229 General purpose industrial valves - Specification of carbon steel castings GB/T 12230 General purpose industrial valves - Specification of stainless steel castings GB/T 12716 Taper pipe threads with 60 degree GB/T 14976 Seamless stainless steel pipes for fluid transport GB/T 16253 Steel castings for pressure purposes JB/T 5263 Specification for steel casting for power station valves JB/T 7248 Technical specification for low temperature service steel casting for valves NB/T 47008 Carbon and alloy steel forgings for pressure equipment NB/T 47009 Alloy steel forgings for low temperature pressure equipment NB/T 47010 Stainless and heat-resisting steel forgings for pressure equipment 3 Styles and parameters 3.1 Nominal pressure 3.1.1 See GB/T 1048 for the definition of nominal pressure. 3.1.2 This part specifies the following 12 PN designated pressure grades: PN2.5, PN6, PN10, PN16, PN25, PN40, PN63, PN100, PN160, PN250, PN320 and PN400. 3.2 Nominal size 3.2.1 See GB/T 1047 for the definition of nominal size. 3.2.2 This part specifies the following 39 DN designated specifications: DN10, DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80, DN100, DN125, DN150, DN200, DN250, DN300, DN350, DN400, DN450, DN500, DN600, DN700, DN800, DN900, DN1000, DN1200, DN1400, DN1600, DN1800, DN2000, DN2200, DN2400, DN2600, DN2800, DN3000, DN3200, DN3400, DN3600, DN3800 and DN4000. 3.3 Outside diameter of Steel pipe Series I and Series II outside diameters of steel pipe are applicable to this part. The nominal size of PN2.5~PN160 pipe flanges and outside diameter of steel pipe shall meet the requirements of Table 1, and those of PN250~PN400 pipe flanges shall meet the requirements of Table 2.   Table 1 Nominal size of PN2.5~PN160 and outside diameter of steel pipe In mm Nominal size/DN Outside diameter of steel pipe Series I Series II 10 17.2 14 15 21.3 18 20 26.9 25 25 33.7 32 32 42.4 38 40 48.3 45 50 60.3 57 65 73.0 76 80 88.9 89 100 114.3 108 125 141.3 133 150 168.3 159 200 219.1 219 250 273.0 273 300 323.9 325 350 355.6 377 400 406.4 426 450 457 480 500 508 530 600 610 630 700 711 720 800 813 820 900 914 920 1000 1016 1020 1200 1219 1220 1400 1422 1420 1600 1626 1620 1800 1829 1820 2000 2032 2020 2200 2235 2220 2400 2438 2420 2600 2642 2620 2800 2845 2820 3000 3048 3020 3200 3251 3220 3400 3454 3420 3600 3658 3620 3800 3861 3820 4000 4064 4020 Table 2 Nominal size of PN250, PN320 and PN400 and outside diameter of steel pipe In mm Nominal size/DN PN250 PN320 PN400 Outside diameter of steel pipe 10 17.2 17.2 17.2 15 21.3 21.3 26.9 20 26.9 26.9 33.7 25 33.7 33.7 42.4 32 42.4 42.4 48.3 40 48.3 48.3 60.3 50 60.3 63.5 76.1 65 76.1 88.9 101.6 80 101.6 101.6 114.3 100 127.0 133.0 139.7 125 152.4 168.3 193.7 150 177.8 193.7 219.1 200 244.5 244.5 273.0 250 298.5 323.9 — 3.4 Types and codes of flanges See Table 3 for types and codes of flanges. See A.1 for the corresponding relationship between this part and EN 1092-1 in terms of code for flange type.

Foreword i Introduction iii 1 Scope 2 Normative references 3 Styles and parameters 3.1 Nominal pressure 3.2 Nominal size 3.3 Outside diameter of Steel pipe 3.4 Types and codes of flanges 3.5 Types and codes of sealing faces 3.6 Flange types and their application scope 4 Type and size of flange 4.1 Size of flange sealing face 4.2 Type and size of flange 5 Technical requirements 5.1 Materials 5.2 Pressure-temperature rating 5.3 Size tolerance 5.4 Joint sealing face 5.5 Fasteners and gaskets 5.6 Welding end type and size 5.7 Machining and manufacturing 6 Test 7 Inspection and acceptance 7.1 Inspection 7.2 Acceptance 8 Marking and labeling 8.1 Marking 8.2 Labeling 9 Supply requirements Annex A (Informative) Corresponding relationship between this part and EN 1092-1 in terms of code for flange type and code for sealing face Annex B (Normative) Welding end type and size Annex C (Informative) Reference sizes of some flanges outside the scope of this part Annex D (Informative) Order contract data of flanges Annex E (Informative) Method for determination of pressure-temperature ratings in EN Annex F (Informative) Reference mass of flange Annex G (Informative) Pipe schedule number and steel pipe wall thickness Bibliography

钢制管法兰 第1部分：PN 系列 1 范围 GB/T 9124的本部分规定了PN 系列钢制管法兰和法兰盖的类型与参数、型式与尺寸、技术要求、试验、检验与验收、标志与标记、供货要求。 本部分适用于公称压力PN2.5～PN400、公称尺寸DN10～DN4000的钢制管法兰和法兰盖。 2 规范性引用文件 下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件，仅注日期的版本适用于本文件。凡是不注日期的引用文件，其最新版本(包括所有的修改单)适用于本文件。 GB/T 152.4 紧固件 六角头螺栓和六角螺母用沉孔 GB/T 700 碳素结构钢 GB/T 711 优质碳素结构钢热轧厚钢板和宽钢带 GB/T 712 船舶及海洋工程用结构钢 GB/T 713 锅炉和压力容器用钢板 GB/T 1047 管道元件 公称尺寸的定义及选用 GB/T 1048 管道元件 公称压力的定义及选用 GB/T 1804 一般公差 未注公差的线性和角度尺寸的公差 GB/T 3531 低温压力容器用低合金钢钢板 GB/T 4237 不锈钢热轧钢板和钢带 GB/T 7306.1 55°密封管螺纹 第1部分：圆柱内螺纹与圆锥外螺纹 GB/T 9125 管法兰连接用紧固件 GB/T 12228 通用阀门 碳素钢锻件技术条件 GB/T 12229 通用阀门 碳素钢铸件技术条件 GB/T 12230 通用阀门 不锈钢铸件技术条件 GB/T 12716 60°圆锥管螺纹 GB/T 14976 流体输送用不锈钢无缝钢管 GB/T 16253 承压铸钢件 JB/T 5263 电站阀门铸钢件技术条件 JB/T 7248 阀门用低温钢铸件技术条件 NB/T 47008 承压设备用碳素钢和合金钢锻件 NB/T 47009 低温承压设备用合金钢锻件 NB/T 47010 承压设备用不锈钢和耐热钢锻件 3 类型与参数 3.1 公称压力 3.1.1 公称压力的定义见GB/T 1048。 3.1.2 本部分规定了公称压力用PN 标识的如下12个压力等级： PN2.5、PN6、PN10、PN16、PN25、PN40、PN63、PN100、PN160、PN250、PN320、PN400。 3.2 公称尺寸 3.2.1 公称尺寸的定义见GB/T 1047。 3.2.2 本部分规定了公称尺寸用DN 标识的如下39个规格： DN10、DN15、DN20、DN25、DN32、DN40、DN50、DN65、DN80、DN100、DN125、DN150、DN200、DN250、DN300、DN350、DN400、DN450、DN500、DN600、DN700、DN800、DN900、DN1000、DN1200、DN1400、DN1600、DN1800、DN2000、DN2200、DN2400、DN2600、DN2800、DN3000、DN3200、DN3400、DN3600、DN3800、DN4000。 3.3 钢管外径 本部分适用的钢管外径为Ⅰ、Ⅱ两个系列。PN2.5～PN160管法兰的公称尺寸和钢管外径应符合表1的规定，PN250～PN400管法兰的公称尺寸和钢管外径应符合表2的规定。 表1 PN2.5～PN160公称尺寸和钢管外径 单位为毫米 公称尺寸 DN 钢管外径 系列 Ⅰ 系列 Ⅱ 10 17.2 14 15 21.3 18 20 26.9 25 25 33.7 32 32 42.4 38 40 48.3 45 50 60.3 57 65 73.0 76 80 88.9 89 100 114.3 108 125 141.3 133 150 168.3 159 200 219.1 219 250 273.0 273 300 323.9 325 350 355.6 377 400 406.4 426 450 457 480 500 508 530 600 610 630 700 711 720 800 813 820 900 914 920 1000 1016 1020 1200 1219 1220 1400 1422 1420 1600 1626 1620 1800 1829 1820 2000 2032 2020 2200 2235 2220 2400 2438 2420 2600 2642 2620 2800 2845 2820 3000 3048 3020 3200 3251 3220 3400 3454 3420 3600 3658 3620 3800 3861 3820 4000 4064 4020 表2 PN250、PN320、PN400的公称尺寸和钢管外径 单位为毫米 公称尺寸 DN PN250 PN320 PN400 钢管外径 10 17.2 17.2 17.2 15 21.3 21.3 26.9 20 26.9 26.9 33.7 25 33.7 33.7 42.4 32 42.4 42.4 48.3 40 48.3 48.3 60.3 50 60.3 63.5 76.1 65 76.1 88.9 101.6 80 101.6 101.6 114.3 100 127.0 133.0 139.7 125 152.4 168.3 193.7 150 177.8 193.7 219.1 200 244.5 244.5 273.0 250 298.5 323.9 — 3.4 法兰类型及代号 法兰类型及代号按表3的规定。本部分与EN1092-1法兰类型代号的对应关系参见附录A中A.1。 表3 法兰的类型及代号 法兰类型 整体法兰 带颈螺纹法兰 对焊法兰 法兰类型代号 IF Th WN 法兰简图 法兰类型 带颈平焊法兰 带颈承插焊法兰 板式平焊法兰 法兰类型代号 SO SW PL 法兰简图 法兰类型 A型对焊环板式松套法兰 B型对焊环板式松套法兰 平焊环板式松套法兰 法兰类型代号 PL/W-A PL/W-B PL/C 法兰简图 法兰类型 管端翻边板式松套法兰 翻边短节板式松套法兰 法兰盖 法兰类型代号 PL/P-A PL/P-B BL 法兰简图 3.5 密封面型式及代号 法兰的密封面型式及代号应符合表4的规定。本部分与EN1092-1法兰密封面代号的对应关系参见附录A 中A.2。 表4 密封面型式及代号 密封面型式 代号 简图 平面 FF 突面 RF 凹凸面 凸面 MF M 凹面 F 榫槽面 榫面 TG T 槽面 G O形圈面 O形圈凸面 OSG OS O形圈槽面 OG 环连接面 RJ 3.6 法兰类型及适用范围 法兰类型及适用范围见表5，表中“√”表示适用，“—”表示不适用。 表5 法兰类型及适用范围 法兰 类型 公称尺寸 DN 公称压力 PN 密封面型式及适用范围 2.5 6 10 16 25 40 63 100 160 250 320 400 整体法兰 (IF) 10 √ √ √ √ √ √ √ √ √ √ √ √ 1)平面 (FF)： PN2.5～PN40； 2)突面 (RF)： PN2.5～PN400； 3)凹凸面 (MF)：PN10～PN400； 4)榫槽面 (TG)：PN10～PN400； 5) O形圈面 (OSG)：PN10～PN40； 6)环连接面 (RJ)：PN63～PN400 15 √ √ √ √ √ √ √ √ √ √ √ √ 20 √ √ √ √ √ √ √ √ √ √ √ √ 25 √ √ √ √ √ √ √ √ √ √ √ √ 32 √ √ √ √ √ √ √ √ √ √ √ √ 40 √ √ √ √ √ √ √ √ √ √ √ √ 50 √ √ √ √ √ √ √ √ √ √ √ √ 65 √ √ √ √ √ √ √ √ √ √ √ √ 80 √ √ √ √ √ √ √ √ √ √ √ √ 100 √ √ √ √ √ √ √ √ √ √ √ √ 125 √ √ √ √ √ √ √ √ √ √ √ √ 150 √ √ √ √ √ √ √ √ √ √ √ √ 200 √ √ √ √ √ √ √ √ √ √ √ √ 250 √ √ √ √ √ √ √ √ √ √ √ — 300 √ √ √ √ √ √ √ √ √ √ — — 350 √ √ √ √ √ √ √ √ — — — — 400 √ √ √ √ √ √ √ — — — — — 450 √ √ √ √ √ √ — — — — — — 500 √ √ √ √ √ √ — — — — — — 600 √ √ √ √ √ √ — — — — — — 700 √ √ √ √ √ — — — — — — — 800 √ √ √ √ √ — — — — — — — 900 √ √ √ √ √ — — — — — — — 1000 √ √ √ √ √ — — — — — — — 1200 √ √ √ √ — — — — — — — — 1400 √ √ √ √ — — — — — — — — 1600 √ √ √ √ — — — — — — — — 1800 √ √ √ √ — — — — — — — — 2000 √ √ √ √ — — — — — — — — 带颈螺纹法兰 (Th) 10 — √ √ √ √ √ √ √ — — — — 1)平面 (FF)：PN6～PN40； 2)突面 (RF)：PN6～PN100 15 — √ √ √ √ √ √ √ — — — — 20 — √ √ √ √ √ √ √ — — — — 25 — √ √ √ √ √ √ √ — — — — 32 — √ √ √ √ √ √ √ — — — — 40 — √ √ √ √ √ √ √ — — — — 50 — √ √ √ √ √ √ √ — — — — 65 — √ √ √ √ √ √ √ — — — — 80 — √ √ √ √ √ √ √ — — — — 100 — √ √ √ √ √ √ √ — — — — 125 — √ √ √ √ √ √ √ — — — — 150 — √ √ √ √ √ √ √ — — — — 对焊法兰 (WN) 10 √ √ √ √ √ √ √ √ √ √ √ √ 1)平面 (FF)：PN2.5～PN40； 2)突面 (RF)：PN2.5～PN400； 3)凹凸面 (MF)：PN10～PN400； 4)榫槽面 (TG)：PN10～PN400； 5) O形圈面 (OSG)：PN10～PN40； 6)环连接面 (RJ)：PN63～PN400 15 √ √ √ √ √ √ √ √ √ √ √ √ 20 √ √ √ √ √ √ √ √ √ √ √ √ 25 √ √ √ √ √ √ √ √ √ √ √ √ 32 √ √ √ √ √ √ √ √ √ √ √ √ 40 √ √ √ √ √ √ √ √ √ √ √ √ 50 √ √ √ √ √ √ √ √ √ √ √ √ 65 √ √ √ √ √ √ √ √ √ √ √ √ 80 √ √ √ √ √ √ √ √ √ √ √ √ 100 √ √ √ √ √ √ √ √ √ √ √ √ 125 √ √ √ √ √ √ √ √ √ √ √ √ 150 √ √ √ √ √ √ √ √ √ √ √ √ 200 √ √ √ √ √ √ √ √ √ √ √ √ 250 √ √ √ √ √ √ √ √ √ √ √ — 300 √ √ √ √ √ √ √ √ √ — — — 350 √ √ √ √ √ √ √ √ — — — — 400 √ √ √ √ √ √ √ — — — — — 450 √ √ √ √ √ √ — — — — — — 500 √ √ √ √ √ √ — — — — — — 600 √ √ √ √ √ √ — — — — — — 700 √ √ √ √ √ — — — — — — — 对焊法兰 (WN) 800 √ √ √ √ √ — — — — — — — 1)平面 (FF)：PN2.5～PN40； 2)突面 (RF)：PN2.5～PN400； 3)凹凸面 (MF)：PN10～PN400； 4)榫槽面 (TG)：PN10～PN400； 5) O形圈面 (OSG)：PN10～PN40； 6)环连接面 (RJ)：PN63～PN400 900 √ √ √ √ √ — — — — — — — 1000 √ √ √ √ √ — — — — — — — 1200 √ √ √ √ — — — — — — — — 1400 √ √ √ √ — — — — — — — — 1600 √ √ √ √ — — — — — — — — 1800 √ √ √ √ — — — — — — — — 2000 √ √ √ √ — — — — — — — — 2200 √ √ √ — — — — — — — — — 2400 √ √ √ — — — — — — — — — 2600 √ √ √ — — — — — — — — — 2800 √ √ √ — — — — — — — — — 3000 √ √ √ — — — — — — — — — 3200 √ √ — — — — — — — — — — 3400 √ √ — — — — — — — — — — 3600 √ √ — — — — — — — — — — 3800 √ — — — — — — — — — — — 4000 √ — — — — — — — — — — — 带颈平焊法兰 (SO) 10 — √ √ √ √ √ √ √ — — — — 1)平面 (FF)：PN6～PN40； 2)突面 (RF)：PN6～PN100； 3)凹凸面 (MF)：PN10～PN100； 4)榫槽面 (TG)：PN10～PN100； 5) O形圈面 (OSG)：PN10～PN40 15 — √ √ √ √ √ √ √ — — — — 20 — √ √ √ √ √ √ √ — — — — 25 — √ √ √ √ √ √ √ — — — — 32 — √ √ √ √ √ √ √ — — — — 40 — √ √ √ √ √ √ √ — — — — 50 — √ √ √ √ √ √ √ — — — — 65 — √ √ √ √ √ √ √ — — — — 80 — √ √ √ √ √ √ √ — — — — 100 — √ √ √ √ √ √ √ — — — — 125 — √ √ √ √ √ √ √ — — — — 150 — √ √ √ √ √ √ √ — — — — 200 — √ √ √ √ √ — — — — — — 250 — √ √ √ √ √ — — — — — — 300 — √ √ √ √ √ — — — — — — 带颈平焊法兰 (SO) 350 — — √ √ √ √ — — — — — — 1)平面 (FF)：PN6～PN40； 2)突面 (RF)：PN6～PN100； 3)凹凸面 (MF)：PN10～PN100； 4)榫槽面 (TG)：PN10～PN100； 5) O形圈面 (OSG)：PN10～PN40 400 — — √ √ √ √ — — — — — — 450 — — √ √ √ √ — — — — — — 500 — — √ √ √ √ — — — — — — 600 — — √ √ √ √ — — — — — — 700 — — — √ — — — — — — — — 800 — — — √ — — — — — — — — 900 — — — √ — — — — — — — — 1000 — — — √ — — — — — — — — 带颈承插焊法兰 (SW) 10 — — — √ √ √ √ √ — — — — 1)平面 (FF)：PN16～PN40； 2)突面 (RF)：PN16～PN100； 3)凹凸面 (MF)：PN16～PN100； 4)榫槽面 (TG)：PN16～PN100； 5) O形圈面 (OSG)：PN16～PN40； 6)环连接面 (RJ)：PN63～PN100