![]() |
中标分类
行业分类
ICS分类
最新标准
|
登录注册 |
您的位置: 标准明细 |
Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative. This standard is formulated with a view to implementing laws and regulations such as "Environmental Protection Law of the People's Republic of China" ,"Law on Prevention of Air Pollution of the People's Republic of China" , and "Decision on Implementing Scientific Concept of Development and Strengthening Environmental Protection by the State Council" as well as "Opinion on Preparing Nationwide Planning for National Main Function Areas by the State Council", to protecting environment, preventing pollution, and promoting the improvement of process and pollution treatment technology in sintering and pelletizing of iron and steel industry. This standard specifies the emission limits, monitoring and supervision requirements of air pollutants for sintering and pelletizing of iron and steel industry. This standard specifies special discharge limits for air pollutants in order to promote harmony development of regional economy and environment, push the adjustment of economic structure and transformation of economic growth mode, and lead the development trend of production process and pollution treatment technology of sintering and pelletizing of iron and steel. The water pollutants, odor pollutants and ambient noise made by sintering and pelletizing of iron and steel enterprise are applicable to the corresponding national standards for the pollutants emission; and the identification, treatment and disposal of the solid waste generated are applicable to the national control standards for the solid waste pollution. This standard is issued for the first time. From the implementation date, the emission control of air pollutants for sintering and pelletizing of iron and steel industry comply with the requirements of this standard instead of those of "Integrated Emission Standards of Air Pollutants" (GB 16297-1996) and "Standard of Smoke and Dust Emission for Industrial Kiln and Furnace" (GB 9078-1996). Provincial people's government may formulate local standard for the pollutant emission for the air pollutants not specified in this standard; and it may also formulate local standards for the pollutants emission stricter than this standard. This national standard was formulated by the Department of Science, Technology and Standards of Ministry of Environmental Protection. Chief drafting organizations of this standard: Design & Research Institute of Anshan Iron and Steel Group Corporation and Environmental Standards Institute of Ministry of Environmental Protection. This standard was approved by the Ministry of Environmental Protection on June 15, 2012. This standard was implemented on October 1, 2012. Ministry of Environmental Protection is responsible for the explanation of this standard. Contents 1 Application Scope 2 2 Normative References 2 3 Terms and Definitions 3 4 Emission Control Requirements of Air Pollutants 4 5 Requirements of Air Pollutants Monitoring 6 6 Implementation and Supervision 7 Emission Standard of Air Pollutants for Sintering and Pelletizing of Iron and Steel Industry 钢铁烧结、球团工业大气污染物排放标准 1 Application Scope This standard specifies the emission limits, monitoring and supervision requirements of air pollutants from sintering and pelletizing of iron and steel enterprises or production facilities, and relevant requirements of implement and supervision of standards. This standard is applicable to the emission management of the air pollutants from sintering and pelletizing of iron and steel enterprises or production facilities, the environmental impact assessment of industrial construction project, environment protection facilities design, completion environmental protection acceptance and the air pollutants emission management after production. This standard is applicable to legal pollutant emission behaviors. The site selection of the pollution source set newly and the management of the current pollution source in the special protection zone shall comply with the relevant regulations in such laws, regulations and rules as "Law on Prevention of Air Pollution of the People's Republic of China", "Law of the People's Republic of China on Prevention and Control of Water Pollution", "Marine Environment Protection Law of the People's Republic of China" ,"Law of the People's Republic of China on Prevention of Environmental Pollution Caused by Solid Waste" and " Law of Environmental Impact Assessment of the People's Republic of China". 2 Normative References This standard takes reference to the provisions in the following documents. GB/T 15432-1995 Ambient Air-Determination of Total Suspended Particulates-Gravimetric Method GB/T 16157-1996 The Determination of Particulates and Sampling Methods of Gaseous Pollutants Emitted from Exhaust Gas of Stationary Source HJ/T 42-1999 Stationary Source Emission - Determination of Nitrogen Oxide - Ultraviolet Spectrophotometric Method HJ/T 43-1999 Stationary Source Emission -- Determination of Nitrogen Oxid – N (1-naphtye) - Ethylenediamine Dihydrochloride Spectrophotometric Method HJ/T 56-2000 Determination of Sulphur Dioxide from Exhausted Gas of Stationary Source Iodine titration Method HJ/T 57-2000 Determination of Sulphur Dioxide from Exhausted Gas of Stationary Source - Fixed-potential Electrolysis Method HJ/T 67-2001 Stationary Source Emission -Determination of Fluoride --Ion Selective Electrode Method HJ/T 77.2-2008 Ambient Air and Waste Gas Determination of Polychlorinated Dibenzo-p-dioxins (PCDDs) and Polychlorinated Dibenzofurans (PCDFs) HJ/T 397-2007 Technical Specifications for Emission Monitoring of Stationary Source "Management Method on Automatic Supervisory Control of Pollution Source" (No. 28 order of the State Environmental Protection Administration of the People's Republic of China) "Environmental Monitoring Management Method" (No.39 order of State Environmental Protection Administration of the People's Republic of China) 3 Terms and Definitions The following terms and definitions are applicable to this standard. 3.1 Sintering It refers to the process that flux and solid fuel are mixed in the required proportion to raw materials containing iron, such as iron powder ore, and pelletized by adding water, and then horizontally laid on the trolley of sintering machine, and the fuel is burned after ignition and air draft, and some of the sintering materials are fused and form blocks. 3.2 Pelletizing It refers to the process that after raw materials (such as iron ore concentrate) and adequate amount of bentonite are uniformly mixed, pellets are produced by pelletizer, and then the pellets are oxidized and consolidated after high temperature roasting. 3.3 Existing enterprises It refers to the sintering and pelletizing production enterprises or production facilities which had put into production or whose environmental impact assessment statements have been approved before the implementation date of this standard. 3.4 New enterprises It refers to the newly-built, rebuilt and extended construction projects of sintering and pelletizing industry whose environmental impact assessment statements are approved after the implementation date of this standard. 3.5 Standard state It refers to the state when the temperature is 273.15K and pressure is 101325 Pa. The air pollutants emission concentration specified in this standard is subject to the dry gas at standard state. 3.6 Sintering (pelletizing) equipment It refers to the sintering machine producing sinter ore (pellet) , including shaft furnace, traveling grate machine and grate-kiln, etc. 3.7 Other production equipment All of the production equipment except sintering (pelletizing) equipment. 3.8 Particulates The generic term of the kiln fume and industrial dust emitted during production process. 3.9 Dioxins The generic term of PCDDs and PCDFs. 3.10 Toxic equivalent factor (TEF) The ratio of dioxins congener and 2, 3, 7, 8- TCDD to the affinity of Ah receptor. 3.11 Toxic equivalent quantity (TEQ) The equivalent concentration when the concentration of dioxins congeners is converted to the equivalent toxicity of 2, 3, 7, 8-TCDD, toxic equivalent quantity concentration is the product of measured concentration and the TEF of the isomer. 4 Emission Control Requirements of Air Pollutants 4.1 From October 1, 2012 to December 31, 2014, the existing enterprises shall implement the specified emission limits of air pollutants in Table 1. Table 1 Air Pollutants Emission Concentration Limits for Existing Enterprises In: mg/m3 (Dioxins is Excluded) Production process or facility Pollutant Limit Position for monitoring pollutant emission Sintering machine Pellet firing equipment Particulates 80 Exhaust funnels in workshops or production facilities Sulfur dioxide 600 Nitrogen oxides (by NO2) 500 Fluoride (by F) 6.0 Dioxins (ng-TEQ/m3) 1.0 Sintering machine tail Traveling grate machine tail Other production equipment Particulates 50 4.2 From January 1, 2015, the existing enterprises shall implement the specified emission limits of air pollutants in Table 2. 4.3 From October 1, 2012, the new enterprises shall implement the specified emission limits of air pollutants in Table 2. Table 2 Air Pollutants Emission Concentration Limits for New Enterprises In: mg/m3 (Dioxins is Excluded) Production process or facility Pollutant Limit Position for monitoring pollutant emission Sintering machine Pellet firing equipment Particulates 50 Exhaust funnels in workshops or production facilities Sulfur dioxide 200 Nitrogen oxides (by NO2) 300 Fluoride (by F) 4.0 Dioxin (ng-TEQ/m3) 0.5 Sintering machine tail Traveling grate machine tail Other production equipment Particulates 30 4.4 Pollutant emission behavior of enterprises shall be controlled strictly according to the environmental protection requirements in the areas where the density of land development is relatively high, the carrying capacity of the environment starts to reduce or the environmental capacity is relatively small, the ecological environment is vulnerable, and where special protection measures are required due to severe environmental pollution problems. The enterprises in these areas shall implement the special emission limits of air pollutants specified in Table 3. The specific territorial scope implementing special emission limits of air pollutants and the implementation time shall be specified by the environmental protection administration department of the State Council or provincial people's government. Table 3 Special Emission Limits of Air Pollutants In: mg/m3 (Dioxins is Excluded) Production process or facility Pollutant Limit Position for monitoring pollutant emission Sintering machine Particulates 40 Exhaust funnels in workshops or production facilities Pellet firing equipment Sulfur dioxide 180 Nitrogen oxides (by NO2) 300 Fluoride (by F) 4.0 Dioxin(ng-TEQ/m3) 0.5 Sintering machine tail Traveling grate machine tail Other production equipment Particulates 20 4.5 The fugitive emission of particulates by enterprise shall comply with the limits specified in Table 4. Table 4 Limits of Fugitive Emission Concentration of Particulates for Existing and New enterprises In: mg/m3 No. Fugitive emission Limit 1 Production workshop with plant 8.0 2 Production workshop without complete plant 5.0 4.6 Environmental protection administration department in charge of supervision shall monitor the environment quality of the sensitive areas used for accommodation, teaching and medical treatment, after production of the existing plant and the environmental protection acceptance for the completed construction project and during the subsequent production process. The specific supervising range of construction project is the surrounding sensitive areas for environmental impact assessment; as for the existing enterprises for which the environmental impact assessment has never been carried out, the supervision range shall be determined by the environmental protection administration department in charge of supervision, based on the emission characteristics and rules of the enterprise, local natural and meteorological conditions as well as the relevant environmental impact assessment technical guide. The local government shall be responsible for the environmental quality of the area under its administration and shall take measures to ensure the environmental conditions meet the requirements of environmental quality standards. 4.7 The production process device generating air pollutants must be provided with partial gas collection system and centralized purifying treatment device to make the emission reach the standard. The height of all exhaust funnels shall not be less than 15m. Where building is within 200m from exhaust funnel, the exhaust funnel shall be 3m higher than the building. 4.8 Before the nation specifies the standard emission amount for products, the measured concentration is temporarily taken as the criterion for judging whether the air pollutants emission reaches the standard or not. 5 Requirements of Air Pollutants Monitoring 5.1 The sampling of the emissions of the enterprises shall be carried out at the specified pollutant emission monitoring position according to the type of the to-be-monitored pollutant; if waste gas treatment facility is available, monitoring shall be carried out behind the facility. Permanent drain outlet mark must be set at the position for monitoring pollutant emission. 5.2 The requirements for the installation of automatic monitoring equipment for the pollutant emission of the new and existing enterprises shall comply with the requirements of relevant laws and "Management Method of Automatic Monitoring for Pollution Source". 5.3 The requirements of monitoring frequency and sampling time for pollutant discharge of enterprises shall comply with the requirements of relevant technical specifications for pollution source monitoring of the nation. Dioxins index shall be monitored once a year. 5.4 The monitoring and sampling for the air pollutants in exhaust funnel shall comply with GB/T 16157 and HJ/T 397. 5.5 The sampling point for fugitive emission of air pollutants shall be at outlets of production building, such as doors and windows, roof or clerestory, wherever the concentration is the maximum. If the fugitive emission source is open-air or roofed but without fence, the monitoring point shall be chosen at any point 5m away from the fume (dust) emission source and with a minimum height of 1.5m, wherever the concentration is the maximum. As for the sampling at the monitoring point of fugitive emission, the average after 1h of continuous sampling or the average of four specimens sampled in equal interval within 1h shall be adopted. 5.6 The enterprises shall monitor the pollution emission according to the requirements of relevant laws and "Management Method for Environmental Monitoring" and save the original monitoring records. 5.7 Air pollutants emission concentration shall be determined according to the method standards listed in Table 5. Table 5 Method Standards for the Air Pollutants Concentration Determination No. Pollutant Name of method standard Standard No. 1 Particulates The Determination of Particulates and Sampling Methods of Gaseous Pollutants Emitted from Exhaust Gas of Stationary Source GB/T 16157-1996 Ambient Air-Determination of Total Suspended Particulates-Gravimetric Method GB/T 15432-1995 2 Sulfur dioxide Determination of Sulphur Dioxide from Exhausted Gas of Stationary Source Iodine titration Method HJ/T 56-2000 Determination of Sulphur Dioxide from Exhausted Gas of Stationary Source - Fixed-potential Electrolysis Method HJ/T 57-2000 3 Nitrogen oxides Stationary Source Emission - Determination of Nitrogen Oxide - Ultraviolet Spectrophotometric Method HJ/T 42-1999 Stationary Source Emission -- Determination of Nitrogen Oxid - N(1-naphtye) - Ethylenediamine Dihydrochloride Spectrophotometric Method HJ/T 43-1999 4 Fluoride Stationary Source Emission -Determination of Fluoride --Ion Selective Electrode Method HJ/T 67-2001 5 Dioxin Ambient Air and Waste Gas Determination of Polychlorinated Dibenzo-p-dioxins(PCDDs)and Polychlorinated Dibenzofurans (PCDFs) HJ/T 77.2-2008 6 Implementation and Supervision 6.1 This standard shall be supervised and implemented by the administrative departments for environmental protection under people's government at above country level. 6.2 In any case, enterprises shall comply with the requirements of pollutant emission control in this standard, and take necessary measures to ensure normal operation of pollution prevention facilities. When conducting supervisory inspection to enterprises, all-level environmental protection departments may adopt the results of on-site and real-time sampling or monitoring as the criteria to judge whether the sewerage behavior meets emission standard and to implement relevant environmental protection management measures. 1 Application Scope 2 Normative References 3 Terms and Definitions 4 Emission Control Requirements of Air Pollutants 5 Requirements of Air Pollutants Monitoring 6 Implementation and Supervision ICS Z 中 华 人 民 共 和 国 国 家 标 准 GB 28662-2012 钢铁烧结、球团工业大气污染物排放标准 Emission standard of air pollutants for sintering and pelletizing of iron and steel industry (发布稿) 本电子稿为发布稿。请以中国环境科学出版社出版的正式标准文本为准。 2012-06-27 发布 2012-10-01 实施 环 境 保 护 部 发布 国家质量监督检验检疫总局 目 次 前 言...............................................................................................................................................II 1 适用范围....................................................................................................................................... 1 2 规范性引用文件........................................................................................................................... 1 3 术语和定义................................................................................................................................... 1 4 大气污染物排放控制要求........................................................................................................... 2 5 大气污染物监测要求................................................................................................................... 4 6 实施与监督................................................................................................................................... 4 前 言 为贯彻《中华人民共和国环境保护法》、《中华人民共和国大气污染防治法》,《国务 院关于落实科学发展观 加强环境保护的决定》等法律、法规和《国务院关于编制全国主体 功能区规划的意见》,保护环境,防治污染,促进钢铁烧结及球团工业生产工艺和污染治理 技术的进步,制定本标准。 本标准规定了钢铁烧结及球团生产企业大气污染物排放限值、监测和监控要求。为促进 地区经济与环境协调发展,推动经济结构的调整和经济增长方式的转变,引导钢铁烧结及球 团生产工艺和污染治理技术的发展方向,本标准规定了大气污染物特别排放限值。 钢铁烧结及球团生产企业排放水污染物、恶臭污染物和环境噪声适用相应的国家污染物 排放标准,产生固体废物的鉴别、处理和处置适用国家固体废物污染控制标准。 本标准为首次发布。 自本标准实施之日起,钢铁烧结及球团生产企业大气污染物排放控制执行本标准的规 定,不再执行《大气污染物综合排放标准》(GB 16297-1996)和《工业炉窑大气污染物排 放标准》(GB 9078-1996)中的相关规定。 地方省级人民政府对本标准未作规定的污染物项目,可以制定地方污染物排放标准;对 本标准已作规定的污染物项目,可以制定严于本标准的地方污染物排放标准。 本标准由环境保护部科技标准司组织制订。 本标准主要起草单位:鞍钢集团设计研究院、环境保护部环境标准研究所。 本标准环境保护部 2012 年 6 月 15 日批准。 本标准自 2012 年 10 月 1 日起实施。 本标准由环境保护部解释。 钢铁烧结、球团工业大气污染物排放标准 1 适用范围 本标准规定了钢铁烧结及球团生产企业或生产设施的大气污染物排放限值、监测和监控 要求,以及标准的实施与监督等相关规定。 本标准适用于现有钢铁烧结及球团生产企业或生产设施的大气污染物排放管理,以及钢 铁烧结及球团工业建设项目的环境影响评价、环境保护设施设计、竣工环境保护验收及其投 产后的大气污染物排放管理。 本标准适用于法律允许的污染物排放行为。新设立污染源的选址和特殊保护区域内现有 污染源的管理,按照《中华人民共和国大气污染防治法》、《中华人民共和国水污染防治法》、 《中华人民共和国海洋环境保护法》、《中华人民共和国固体废物污染环境防治法》、《中华 人民共和国环境影响评价法》等法律、法规、规章的相关规定执行。 2 规范性引用文件 本标准内容引用了下列文件中的条款。 GB/T 15432-1995 环境空气 总悬浮颗粒物的测定 重量法 GB/T 16157-1996 固定污染源排气中颗粒物测定与气态污染物采样方法 HJ/T 42-1999 固定污染源排气中氮氧化物的测定 紫外分光光度法 HJ/T 43-1999 固定污染源排气中氮氧化物的测定 盐酸萘乙二胺分光光度法 HJ/T 56-2000 固定污染源排气中二氧化硫的测定 碘量法 HJ/T 57-2000 固定污染源排气中二氧化硫的测定 定电位电解法 HJ/T 67-2001 大气固定污染源 氟化物的测定 离子选择电极法 HJ/T 77.2-2008 环境空气和废气 二噁英类的测定 同位素稀释高分辨气相色谱-高 分辨质谱法 HJ/T 397-2007 固定源废气监测技术规范 《污染源自动监控管理办法》(国家环境保护总局令第 28 号) 《环境监测管理办法》(国家环境保护总局令第 39 号) 3 术语和定义 下列术语和定义适用于本标准。 3.1 烧结 铁粉矿等含铁原料加入熔剂和固体燃料,按要求的比例配合,加水混合制粒后,平铺在 烧结机台车上,经点火抽风,使其燃料燃烧,烧结料部分熔化粘结成块状的过程。 3.2 球团 铁精矿等原料与适量的膨润土均匀混合后,通过造球机造出生球,然后高温焙烧,使球 团氧化固结的过程。 3.3 现有企业 指在本标准实施之日前建成投产或环境影响评价文件已通过审批的烧结及球团生产企 业或生产设施。 3.4 新建企业 指本标准实施之日起环境影响评价文件通过审批的新建、改建和扩建的烧结及球团工业 建设项目。 3.5 标准状态 温度为 273.15K,压力为 101325Pa 时的状态。本标准规定的大气污染物排放浓度均以 标准状态下的干气体为基准。 3.6 烧结(球团)设备 生产烧结矿(球团矿)的烧结机,包括竖炉、带式焙烧机和链箅机-回转窑等设备。 3.7 他生产设备 除烧结(球团)设备以外的所有生产设备。 3.8 颗粒物 生产过程中排放的炉窑烟尘和生产性粉尘的总称。 3.9 二噁英类 多氯代二苯并-对-二噁英(PCDDs)和多氯代二苯并呋喃(PCDFs)的统称。 3.10 毒性当量因子(TEF) 二噁英类同类物与 2,3,7,8-四氯代二苯并-对-二噁英对 Ah 受体的亲和性能之比。 3.11 毒性当量(TEQ) 各二噁英类同类物浓度折算为相当于 2,3,7,8-四氯代二苯并-对-二噁英毒性的等价浓度, 毒性当量浓度为实测浓度与该异构体的毒性当量因子的乘积。 4 大气污染物排放控制要求 4.1 自 2012 年 10 月 1 日起至 2014 年 12 月 31 日止,现有企业执行表 1 规定的大气污染物 排放限值。 表1 现有企业大气污染物排放浓度限值 单位:mg/m3(二噁英类除外) 生产工序或设施 污染物项目 限值 污染物排放监控位置 烧结机 球团焙烧设备 颗粒物 80 车间或生产设施排气筒 二氧化硫 600 氮氧化物(以 NO2 计) 500 氟化物(以 F 计) 6.0 二噁英类(ng-TEQ/m3) 1.0 烧结机机尾 带式焙烧机机尾 其他生产设备 颗粒物 50 4.2 自 2015 年 1 月 1 日起,现有企业执行表 2 规定的大气污染物排放限值。 4.3 自 2012 年 10 月 1 日起,新建企业执行表 2 规定的大气污染物排放限值。 表2 新建企业大气污染物排放浓度限值 单位:mg/m3(二噁英类除外) 生产工序或设施 污染物项目 限值 污染物排放监控位置 烧结机 球团焙烧设备 颗粒物 50 车间或生产设施排气筒 二氧化硫 200 氮氧化物(以 NO2 计) 300 氟化物(以 F 计) 4.0 二噁英类(ng-TEQ/m3) 0.5 烧结机机尾 带式焙烧机机尾 其他生产设备 颗粒物 30 4.4 根据环境保护工作的要求,在国土开发密度已经较高、环境承载能力开始减弱,或环境 容量较小、生态环境脆弱,容易发生严重环境污染问题而需要采取特别保护措施的地区,应 严格控制企业的污染物排放行为,在上述地区的企业执行表 3 规定的大气污染物特别排放限 值。 执行大气污染物特别排放限值的地域范围、时间,由国务院环境保护行政主管部门或省 级人民政府规定。 表3 大气污染物特别排放限值 单位:mg/m3(二噁英类除外) 生产工序或设施 污染物项目 限值 污染物排放监控位置 烧结机 颗粒物 40 车间或生产设施排气筒 球团焙烧设备 二氧化硫 180 氮氧化物(以 NO2 计) 300 氟化物(以 F 计) 4.0 二噁英类(ng-TEQ/m3) 0.5 烧结机机尾 带式焙烧机机尾 其他生产设备 颗粒物 20 4.5 企业颗粒物无组织排放执行表 4 规定的限值。 表4 现有和新建企业颗粒物无组织排放浓度限值 单位:mg/m3 序号 无组织排放源 限值 1 有厂房生产车间 8.0 2 无完整厂房车间 5.0 4.6 在现有企业生产、建设项目竣工环保验收及其后的生产过程中,负责监管的环境保护行 政主管部门,应对周围居住、教学、医疗等用途的敏感区域环境空气质量进行监测。建设项 目的具体监控范围为环境影响评价确定的周围敏感区域;未进行过环境影响评价的现有企 业,监控范围由负责监管的环境保护行政主管部门,根据企业排污的特点和规律及当地的自 然、气象条件等因素,参照相关环境影响评价技术导则确定。地方政府应对本辖区环境质量 负责,采取措施确保环境状况符合环境质量标准要求。 4.7 产生大气污染物的生产工艺装置必须设立局部气体收集系统和集中净化处理装置,达标 排放。所有排气筒高度应不低于 15m。排气筒周围半径 200m 范围内有建筑物时,排气筒高 度还应高出最高建筑物 3m 以上。 4.8 在国家未规定生产单位产品基准排气量之前,以实测浓度作为判定大气污染物排放是否 达标的依据。 5 大气污染物监测要求 5.1 对企业排放废气的采样应根据监测污染物的种类,在规定的污染物排放监控位置进行, 有废气处理设施的,应在该设施后监控。在污染物排放监控位置须设置永久性排污口标志。 5.2 新建企业和现有企业安装污染物排放自动监控设备的要求,按有关法律和《污染源自动 监控管理办法》的规定执行。 5.3 对企业污染物排放情况进行监测的频次、采样时间等要求,按国家有关污染源监测技术 规范的规定执行。二噁英类指标每年监测一次。 5.4 排气筒中大气污染物的监测采样按 GB/T 16157、HJ/T 397 规定执行。 5.5 大气污染物无组织排放的采样点设在生产厂房门窗、屋顶、气楼等排放口处,并选浓度 最大值。若无组织排放源是露天或有顶无围墙,监测点应选在距烟(粉)尘排放源 5m,最 低高度 1.5m 处任意点,并选浓度最大值。无组织排放监控点的采样,采用任何连续 1h 的 采样计平均值,或在任何 1h 内,以等时间间隔采集 4 个样品计平均值。 5.6 企业应按照有关法律和《环境监测管理办法》的规定,对排污状况进行监测,并保存原 始监测记录。 5.7 对大气污染物排放浓度的测定采用表 5 所列的方法标准。 表5 大气污染物浓度测定方法标准 序号 污染物项目 方法标准名称 标准编号 1 颗粒物 固定污染源排气中颗粒物测定与气态污染物采样方法 GB/T 16157-1996 环境空气 总悬浮颗粒物的测定 重量法 GB/T 15432-1995 2 二氧化硫 固定污染源排气中二氧化硫的测定 碘量法 HJ/T 56-2000 固定污染源排气中二氧化硫的测定 定电位电解法 HJ/T 57-2000 3 氮氧化物 固定污染源排气中氮氧化物的测定 紫外分光光度法 HJ/T 42-1999 固定污染源排气中氮氧化物的测定 盐酸萘乙二胺分光光度法 HJ/T 43-1999 4 氟化物 大气固定污染源 氟化物的测定 离子选择电极法 HJ/T 67-2001 5 二噁英类 环境空气和废气 二噁英类的测定 同位素稀释高分辨气相色 谱-高分辨质谱法 HJ/T 77.2-2008 6 实施与监督 6.1 本标准由县级以上人民政府环境保护行政主管部门负责监督实施。 6.2 在任何情况下,企业均应遵守本标准的大气污染物排放控制要求,采取必要措施保证污 染防治设施正常运行。各级环保部门在对企业进行监督性检查时,可以现场即时采样或监测 的结果,作为判定排污行为是否符合排放标准以及实施相关环境保护管理措施的依据。 |
联系我们
|
微信联系客服
![]() |
关于我们 | 联系我们 | 收费付款 |
服务热线:400-001-5431 | 电话:010-8572 5110 | 传真:010-8581 9515 | Email: bz@bzfyw.com | |
版权所有: 北京悦尔信息技术有限公司 2008-2020 京ICP备17065875号-1 |
本页关键词: |
GB 28662-2012, GB/T 28662-2012, GBT 28662-2012, GB28662-2012, GB 28662, GB28662, GB/T28662-2012, GB/T 28662, GB/T28662, GBT28662-2012, GBT 28662, GBT28662 |