1 Scope
This Part specifies the technical requirements, test methods and inspection rules for standard wall insulation cables up to AC 3 kV on board rolling stock (including multiple units).
This Part is applicable to rolling stock (including multiple units), and other rail vehicles may also refer to the provisions of this Part.
2 Normative References
The following documents for the application of this document are essential. Any dated reference, just dated edition applies to this document. For undated references, the latest edition (including any amendments) applies to this document.
GB 252-2000 Light Diesel Fuels
GB/T 2900.10-2001 Electrotechnical Vocabulary - Electric Cables (IEC 60050-461: 1984, IDT)
GB/T 2951.11-2008 Common Test Methods for Insulating and Sheathing Materials of Electric and Optical Cables - Part 11: Methods for General Application - Measurement of Thickness and Overall Dimensions - Tests for Determining the Mechanical Properties (IEC 60811-1-1: 2001, IDT)
GB/T 2951.12-2008 Common Test Methods for Insulating and Sheathing Materials of Electric and Optical Cables - Part 12: Methods for General Application - Thermal Ageing Methods (IEC 60811-1-2: 1985, IDT)
GB/T 2951.13-2008 Common Test Methods for Insulating and Sheathing Materials of Electric and Optical Cables - Part 13: Methods for General Application - Measurement for Determining the Density - Water Absorption Tests - Shrinkage Test (IEC 60811-1-3: 2001, IDT)
GB/T 2951.14-2008 Common Test Methods for Insulating and Sheathing Materials of Electric and Optical Cables - Part 14: Methods for General Application - Test at Low Temperature (IEC 60811-1-4: 1985, IDT)
GB/T 2951.21-2008 Common Test Methods for Insulating and Sheathing Materials of Electric and Optical Cables - Part 21: Methods Specific to Elastomeric Compounds - Ozone Resistance, Hot Set and Mineral Oil Immersion Tests (IEC 60811-2-1: 2001, IDT)
GB/T 3048.4-2007 Test Methods for Electrical Properties of Electric Cables and Wires - Part 4: Test of DC Resistance of Conductors
GB/T 3048.5-2007 Test Methods for Electrical Properties of Electric Cables and Wires - Part 5: Test of Insulation Resistance
GB/T 3048.8-2007 Test Methods for Electrical Properties of Electric Cables and Wires - Part 8: AC Voltage Test
GB/T 3048.9-2007 Test Methods for Electrical Properties of Electric Cables and Wires - Part 9: Spark Test of Insulated Cores
GB/T 3956-2008 Conductors of Insulated Cables (IEC 60228: 2004, IDT)
GB/T 4909.2-2009 Test Methods for Bare Wires - Part 2: Measurement of Dimensions
GB/T 4909.3-2009 Test Methods for Bare Wires - Part 3: Tensile Test
GB/T 4909.11-2009 Test Methods for Bare Wires - Part 11: Test for Adherence of Coating
GB/T 4910-2009 Tinned Round Copper Wire
GB/T 6995 Markings for Electric Wires and Cables
GB/T 12528-2008 Rail Vehicle Cables with Rated Voltages up to and Including 3kV
GB/T 17650.1-1998 Test on Gases Evolved during Combustion of Materials from Cables - Part 1: Determination of the Amount of Halogen Acid Gas (idt IEC 60754-2: 1991)
GB/T 17650.2-1998 Test on Gases Evolved during Combustion of Materials from Cables - Part 2: Determination of Degree of Acidity of Gases by Measuring pH and Conductivity (idt IEC 60754-2: 1991)
GB/T 17651.2-1998 Measurement of Smoke Density of Cables Burning under Defined Conditions - Part 2: Test Procedure and Requirements (idt IEC 61034-2: 1997)
GB/T 18380.12-2008 Test on Electric and Optical Fibre Cables under Fire Conditions - Part 12: Test for Vertical Flame Propagation for a Single Insulated Wire or Cable - Procedure for 1kW Pre-mixed Flame (IEC 60332-1-2: 2004, IDT)
GB/T 18380.35-2008 Tests on Electric and Optical Fibre Cables under Fire Conditions - Part 35: Test for Vertical Flame Spread of Vertically-mounted Bunched Wires or Cables - Category C (IEC 60332-3-24: 2000, IDT)
SH/T 0139-1995 Axle Oil
EN 50305: 2002 Railway Applications - Railway Rolling Stock Cables Having Special Fire Performance - Test Methods
3 Terms and Definitions
For the purposes of this document, the terminologies and definitions given in GB/T 2900.10-2001 as well as the following ones apply.
3.1
Rated voltage
The reference voltage for cable construction design and electrical property test, expressed by U0, in V.
Foreword i
1 Scope
2 Normative References
3 Terms and Definitions
4 Classification, Code, Specification and Construction of Cable
5 Technical Requirements
6 Electric Properties
7 Safety Property
8 Inspection Rules and Methods
9. Delivery Conditions
10 Packaging, Transportation and Storage of Cable
Appendix A (Normative) Test Method for Corona-resistant Lifetime(3 kV cables)
