Ships and Marine Technology — Ship's Mooring and Towing Fittings — Shipside Roller Fairleads
1 Scope
This standard specifies the design, size and technical requirements for shipside roller fairleads.
This standard is applicable to the design, manufacture and acceptance of shipside roller fairleads.
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 13755 Ships and Marine Technology — Ship's Mooring and Towing Fittings — Steel Rollers
IMO Circular MSC/
Circ.1175 Guidance on Shipboard Towing and Mooring Equipment
3 Terms and Definitions
For the purposes of this document, the following terms and definitions apply.
3.1
safe working load (SWL)
maximum load, in kN, on the rope that should normally be applied in service conditions
4 Classification
4.1 Types
Depending on the construction, roller fairleads shall be classified as the following two types:
— 2-roller type;
— 3-roller type.
4.2 Nominal sizes
The nominal sizes, Dn, of roller fairleads are denoted by reference to the outside diameter of the roller, in millimeters, from a basic series of preferred numbers. The nominal sizes are: 150, 200, 250, 300, 350, 400, 450 and 500.
5 Dimensions
Roller fairleads have dimensions and particulars in accordance with Tables 1 and 2, and Figures 1 and 2.
a) 2-roller type b) 3-roller type
Figure 1 Layout of roller fairleads
Table 1 Dimensions and SWL of roller fairleads
Dimensions in millimeters
Nominal size Dn 2-roller type 3-roller type l1 l2 Pe SWLb
l We l We θa = 90° θa = 20°
kN t kN t
a θ is the relative angle of ropes on the roller fairlead (refer to Annex A).
b The SWL is the maximum applicable rope tension based on 90° (θ = 90°) and 160° (θ = 20°) deflection of rope direction by the roller fairlead.
The SWLs shown in this table are for reference only. These are based on the loadings as mentioned in Annex A.
The “SWL” may be adjusted depending on the actual loading conditions, and the actual marking shall be agreed between the user and the manufacturer.
c P and W are for reference only. The opening size on the shell or bulwark shall be determined considering overhauling space of the roller.
Dimensions in millimeters
Key:
1 — seat;
2 — steel rollers.
H: The height of the roller fairlead shall be determined in accordance with the height of the shipside gutter coaming.
α: The inclination of α° is to be determined in accordance with the rope leading inclination.
Note: The end shape of the fairleads shown in “Detail Y” can be changed as per manufacturer’s standard based on no sharp edges to avoid rope damage.
Foreword II
1 Scope
2 Normative References
3 Terms and Definitions
4 Classification
5 Dimensions
6 Materials
7 Manufacturing and Inspection
8 Marking
Annex A (Informative) Basis for Strength Assessment of Shipside Roller Fairleads
Annex NA (Informative) Marking
Bibliography
ICS 47.020.50
U 21
GB
中华人民共和国国家标准
GB/T 37448—2019/ISO 13767:2012
船舶和海上技术 船舶系泊和拖带设备
舷边滚轮导缆器
Ships and marine technology—Ship’s mooring and towing fittings—
Shipside roller fairleads
(ISO 13767:2012,IDT)
2019-05-10发布 2019-12-01实施
国家市场监督管理总局
中国国家标准化管理委员会 发布
前 言
本标准按照GB/T 1.1—2009给出的规则起草。
本标准使用翻译法等同采用ISO 13767:2012《船舶和海上技术 船舶系泊和拖带设备 舷边滚轮导缆器》。
与本标准中规范性引用的国际文件有一致性对应关系的我国文件如下:
——GB/T 36664—2018 船舶和海上技术 船舶系泊和拖带设备 导缆滚轮(ISO 13755:2012,IDT)。
本标准做了下列编辑性修改:
——增加了资料性附录NA,对标记进行说明。
本标准由全国船舶舾装标准化技术委员会(SAC/TC 129)提出并归口。
船舶和海上技术 船舶系泊和拖带设备
舷边滚轮导缆器
1 范围
本标准规定了舷边滚轮导缆器的分类、尺寸以及技术要求。
本标准适用于舷边滚轮导缆器的设计、制造和验收。
2 规范性引用文件
下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件,仅注日期的版本适用于本文件。凡是不注日期的引用文件,其最新版本(包括所有的修改单)适用于本文件。
ISO 13755 船舶和海上技术 船舶系泊和拖带设备 导缆滚轮(Ships and marine technology—Ship’s mooring and towing fittings—Steel rollers)
IMO Circular MSC/Circ. 1175 船舶拖带和系泊设备指南(Guidance on shipboard towing and mooring equipment)
3 术语和定义
下列术语和定义适用于本文件。
3.1
安全工作负荷 safe working load;SWL
在正常工作条件下系泊索允许承受的最大负荷,单位为千牛(kN)。
4 分类
4.1 型式
舷边滚轮导缆器按照结构分为以下两种型式:
——双滚轮型;
——三滚轮型。
4.2 公称尺寸
舷边滚轮导缆器的公称尺寸Dn用以毫米为单位的滚轮外直径最小处的尺寸表示。分别为150、200、250、300、350、400、450和500。
5 尺寸
舷边滚轮导缆器的结构和尺寸按表1、表2、图1和图2。
船体/舷墙开孔
a) 双滚轮型 b) 三滚轮型
图1 舷边滚轮导缆器布置示意图
表1 舷边滚轮导缆器尺寸及安全工作负荷 单位为亳米
公称尺寸Dn 双滚轮型 三滚轮型 l1 l2 Pe 安全工作负荷b
l We l We θa=90° θa=20°
kN t kN t
a θ是经过舷边滚轮导缆器的系泊索形成的夹角(参见附录A)。
b 安全工作负荷(SWL)是基于缆绳通过滚轮形成的夹角为90°(即θ=90°)与20°(即θ=20°,包角为160°)的状态核算得出的缆绳可承受的最大拉力。
表中安全工作负荷按照附录A的评定方法得出,仅供参考。
安全工作负荷可以根据实际的负荷状态进行调整,实际标示的安全工作负荷应是制造厂和使用方共同认可的数值。
c P和W尺寸仅供参考。船体外板或者舷墙开孔大小的确定应考虑滚轮拆卸空间的需求。
单位为毫米
排水孔
水密
SWL标志
下方加强结构
甲板
约50
打磨光顺
说明:
1——基座;
2——钢质导缆滚轮。
H:滚轮导缆器的高度取决于舷侧顶板的高度。
α:倾斜角α应与系泊索导缆时倾斜度一致。
注:“详图Y”所示的导缆器的外端面形状按照无锐边以避免造成系泊索损坏的原则,可以采用不同于本图的制造厂标准。
图2 舷边滚轮导缆器结构示意图
注:图2适用于甲板栏杆式,船体/舷墙开孔式可参考。
表2 舷边滚轮导缆器尺寸规格 单位为毫米
公称尺寸Dn A B C R dc h1 t1 t2 焊脚长度a 计算重量b
A型、B型 C型 z1 z2 z3 双滚轮型 三滚轮型
a 采用各类开坡口型式焊接时,可不必遵循表中的焊脚长度,但应确保与本标准规定的焊脚长度等同的焊接容量/强度。
b 计算重量是滚轮导缆器H为380 mm的重量,不包括其上的钢质导缆滚轮,供参考。
c 尺寸d的大小应根据钢质导缆滚轮的类型(A型、B型和C型)来决定,钢质导缆滚轮按ISO 13755。
6 材料
舷边滚轮导缆器底座的材料应为屈服强度不小于235 N/mm2的可焊钢板。
7 制造和检查
7.1 舷边滚轮导缆器的所有表面应没有可见瑕疵或缺陷。
7.2 所有与系泊索接触的表面应光顺,无毛刺。
7.3 舷边滚轮导缆器的外表面应至少涂一道防锈漆。
8 标志
8.1 按照IMO Circular MSC/Circ.1175的规定,舷边滚轮导缆器的SWL应标示在船上拖带和系泊布置图中,供船长参照使用。
8.2 舷边滚轮导缆器在船上实际能承受的SWL还取决于安装位置甲板下方的结构加强情况,该实际SWL应标示在拖带和系泊布置图中。实际SWL不应超过本标准规定的SWL。
8.3 舷边滚轮导缆器应以堆焊或者等同的方式清晰地标出SWL。SWL标志应以吨(符号“t”)为单位,标志的位置不应在系泊操作过程中被遮挡。
示例: SWL ×××t
注1:实际标注时,按相关船级社、国家法定计量单位及用户的要求,可使用千牛(kN)。
注2:舷边滚轮导缆器的产品标记参见附录NA。
附录 A
(资料性附录)
舷边滚轮导缆器的强度评定
A.1 通则
舷边滚轮导缆器的强度是按照以下设计准则,使用有限元模型分析进行评估确定的。
A.2 负荷
舷边滚轮导缆器按可以承受水平和垂直两种工况设计。水平负荷与垂直负荷考虑为单独出现,不考虑两种负荷同时出现的情况。
A.2.1 舷边滚轮导缆器水平负荷见图A.1。
加载点
加载点详图
说明:
P——作用在导缆滚轮直径最小处的系泊索上的系泊力与拖带力。
注1:如图所示,水平负荷考虑了系泊索通过导缆滚轮形成160°包角(θ=20°)时的情况。
注2:系泊索上的负荷可以随着系泊索形成的包角小于160°而对应增加。
图A.1 舷边滚轮导缆器的水平负荷
A.2.2 舷边滚轮导缆器垂直负荷见图A.2。
说明:
P——作用在导缆滚轮直径最小处的系泊索上的系泊力与拖带力。
注:如图所示,垂直负荷是考虑了系泊索通过滚轮导缆器产生偏移时的情况。
舷外垂直向下角度:舷外向下90°。
舷外垂直向上角度:不做考虑。
角度“α”根据从系泊绞车绳筒导出的系泊索的情况确定。
图A.2 舷边滚轮导缆器的垂直负荷
A.2.3 单一负荷情况适用于双滚轮型导缆器,同时加载情况适用于三滚轮型导缆器。
A.3 负荷和应力衡准
在SWL下,舷边滚轮导缆器的合成应力应不超过材料屈服强度的85%。
A.4 磨损余量和腐蚀裕度
磨损余量和腐蚀裕度已包括在安全系数中。
附录 NA
(资料性附录)
标 记
NA.1 型号表示方法
舷边滚轮导缆器的型号表示方法如下:
公称尺寸的数值
类型:双滚轮型——2
三滚轮型——3
NA.2 标记示例
双滚轮型、公称尺寸为350的舷边滚轮导缆器标记如下:
舷边滚轮导缆器GB/T 37448—2019 2×350
三滚轮型、公称尺寸为450的舷边滚轮导缆器标记如下:
舷边滚轮导缆器 GB/T 37448—2019 3×450
参考文献
[1] IACS UR A2,Shipboard fittings and supporting hull structures associated with towing and mooring on conventional vessels
[2] OCIMF,Mooring Equipment Guidelines (MEG3)