标准编号:	CCAP-GZ-6800-2025
中文名称:	机动车辆产品CCAP标志认证实施规则 汽车座椅及座椅头枕
英文名称:	Implementation Rules for CCAP Mark Certification of Motor Vehicle Products Seat and Seat Headrest Products for Motor Vehicles
行业分类:	CC
发布日期:	2025-02-25
实施日期:	2025-2-25
标准状态:	现行
替代旧标准:	CCAP-GZ-6800:2020 机动车辆产品CCAP标志认证实施规则 汽车座椅及座椅头枕
翻译语言:	英文
文件格式:	PDF
中文字符数:	30000 字
翻译价格(元):	4500.00 元
交付时间:	付款后 1 个工作日

No.: CCAP-GZ-6800:2025





Implementation Rules for CCAP Mark Certification of Motor Vehicle Products





Seat and seat headrest products for motor vehicles



汽车座椅及座椅头枕



(English Translation)











































Issue date: 2025-02-25 Implementation date: 2025-02-25



China Certification Center for Automotive Products Co., Ltd.





Contents



1 Application scope 1

2 Certification standards 1

3 Selection of certification modes and related requirements 1

3.1 Basic certification mode 1

3.2 Applicability of certification modes 2

4 Certification unit division 2

5 Certification application 4

5.1 Submission and acceptance of certification application 4

5.2 Certification application data 5

5.3 Certification scheme and certification contract 7

6 Implementation of certification 7

6.1 Type test 7

6.2 Initial factory inspection 12

6.3 Certification evaluation and decision 15

6.4 Certification time limit 15

6.5 Service components of discontinued-production vehicle models 16

6.6 Special provisions for "issuing the certificate first and then inspecting the factory" within the same producer (manufacturer) 16

7 Post-certification supervision 16

7.1 Post-certification follow-up inspection 17

7.2 Sampling testing or inspection on production site 18

7.3 Market sampling testing or inspection 19

7.4 Frequency and time of post-certification supervision 19

7.5 Record of post-certification supervision 20

7.6 Evaluation of post-certification supervision results 20

8 Certification certificate 20

8.1 Maintenance of certification certificate 20

8.2 Contents of certification certificate 20

8.3 Change and extension of certification certificate 21

8.4 Cancellation, suspension and revocation of certification certificate 23

8.5 Use of certification certificate 23

9 Certification mark 23

10 Charges 23

11 Certification responsibilities 24

12 Process and timeline requirements related to technical disputes, complaints, and appeals 24

Annex 1 Description of seat and seat headrest products for motor vehicles 25

Annex 2 List of key components/materials for seat and seat headrest products for motor vehicles 27

Annex 3 CoP requirements 29

Appendix 1 Requirements for quality assurance capacity of factory 32

Annex 4 Requirements for the preparation of the CoP control plan and execution report 38

Appendix 1 Recommended format for CoP control plan 42

Appendix 2 Product COP testing and inspection plan 45

Annex 5 Implementation of certification of after-sales service spare parts for discontinued-production vehicle models 46

Annex 6 Principles of production enterprise classification 48

Annex 7 Requirements for testing by utilizing testing resources of production enterprises and utilization of other conformity assessment results 51







Foreword



The Rules are formulated and issued by China Certification Center for Automotive Products Co., Ltd. (CCAP), of which the copyright belongs to CCAP. No organization or individual is allowed to use them, in whole or in part, in any form without the permission of CCAP.



Revision history of the Rules:



On August 10, 2020, the Rules were revised as CCAP-GZ-6800:2020, replacing CCAP-GZ-6800:2019. The main technical changes are as follows:



(1) The certification scope has been revised to include the seats and seat headrests for Classes A and I motor vehicles within the Categories M2 and M3 motor vehicles, changing to "applicable to seat and seat headrest products for Categories M and N motor vehicles", and clarifying the scope of non-application;



(2) The certification standards have been revised, with GB 15083-2006 being deleted;



(3) The implementation requirements for type test have been revised in accordance with the certification standards;



(4) The requirements for post-certification supervision sampling testing have been clarified;



(5) Annex 1-3 "Description of organic materials used in seat and seat headrest products for motor vehicles" has been added;



(6) The structure of the Rules has been adjusted, with the order of some annexes being changed, and Annex 6 "Principles of production enterprise classification" and Annex 7 "Requirements for testing by utilizing testing resources of production enterprises and utilization of other certification results" have been added.



The main technical changes in the revision on June 18, 2021 are as follows:



(1) The certification standard GB 38262-2019 Flammability of interior materials for buses has been added;



(2) Type test items and COP test items for bus seat interior materials to which GB 38262-2019 is applicable have been added;



(3) Product description parameters related to bus seat interior materials have been added.





The main technical changes in the revision on September 9, 2024 are as follows:



(1) The certification standard GB 11550-2009 has been abolished and deleted; the certification standard GB 13057-2014 has been revised to GB 13057-2023; the certification standard GB 24406-2024 Strength of student seat and their anchorages of special school bus has been added (see Clause 2);



(2) The subclause "Special provisions for ‘issuing the certificate first and then inspecting the factory’ within the same producer (manufacturer)" has been added (see 6.6);



(3) The description of products has been updated (see Annex 1);



(4) The validity period of the certificate has been changed to ten years (see 8.1);



(5) Some editorial adjustments have been made to the textual description of the Implementation Rules.



On February 25, 2025, the serial number of the Implementation Rules was revised from CCAP-GZ-6800:2020 to CCAP-GZ-6800:2025. In addition to editorial adjustments to the text and document structure, other main technical changes are as follows:



(1) The "Certification standards" has been modified, with GB 24406-2012 being deleted (see Clause 2);



(2) The unit division principles have been revised (see Clause 4);



(3) The subclause "Requirements for type test samples" has been modified (see 6.1.2.1);



(4) The content of sampling testing or inspection on production site during post-certification supervision has been modified (see 7.2.2);



(5) The relevant provisions of the subclause "Change and extension of certification certificate" have been modified (see 8.3);



(6) The relevant requirements of the clause "Certification mark" have been modified, with addition of requirements for the use and management of CCC mark (see Clause 9);



(7) The description of products has been changed (see Annex 1);



(8) The annex "Principles of production enterprise classification" has been modified (see Annex 6);





(9) The provisions of the annex "Requirements for testing by utilizing testing resources of production enterprises and utilization of other conformity assessment results" has been modified (see Annex 7).



Formulated by: China Certification Center for Automotive Products Co., Ltd.





1 Application scope



The Rules are applicable to seat and seat headrest products for Categories M and N motor vehicles, but not to the following seats and seat headrests:



(1) Rearward-facing seats and headrests installed on them;



(2) Seats or restraint systems for child occupants;



(3) Sleeper berths in buses and trucks;



(4) Components that constitute the seat assembly, such as seat frame and seat surface cover;



(5) Parts that constitute the headrest assembly, such as headrest frame and headrest surface cover.



Any adjustment to the application scope due to any change(s) in laws and regulations or related product standards, technologies, industrial polices and other factors shall be subject to the announcement issued by CCAP.



2 Certification standards



GB 15083-2019 Strength requirement and test method of automobile seats, their anchorages and any head restraints

GB 13057-2023 Strength of seats and their anchorages of passenger vehicles

GB 24406-2024 Strength of student seat and their anchorages of special school bus

GB 8410-2006 Flammability of automotive interior materials

GB 38262-2019 Flammability of interior materials for buses



The production enterprises shall fully comply with the mandatory requirements of laws, regulations, and standards related to seat and seat headrest products for motor vehicles promulgated by the nation, and meet the corresponding requirements.



In principle, the latest versions of the above standards, as issued by the national competent administrative department of standardization, shall apply. Any use of other editions of these standards, where necessary, shall be subject to the announcements issued by CCAP regarding the requirements of relevant applicable standards.



3 Selection of certification modes and related requirements



3.1 Basic certification mode



The basic certification mode for implementing the CCAP mark certification of seat and seat headrest products for motor vehicles is:



Type test + initial factory inspection + post-certification supervision



The basic certification mode is determined based on the inherent safety risk characteristics of products and the production technologies commonly adopted by the production enterprises, on the premise of integrity and self-discipline, effective management and stable production of the production enterprises.



The post-certification supervision refers to the supervision of the certified products and their production enterprises by CCAP, which is carried out by one or a combination of the three modes, namely, post-certification follow-up factory inspection, sampling testing or inspection on production site, and market sampling testing or inspection.



3.2 Applicability of certification modes



Following the principles of production enterprise classification, CCAP will appropriately add/reduce certification elements for combination as necessary for an enterprise depending on its type on the basis of the basic certification mode. This includes:



For Types A and B production enterprises: The post-certification supervision may be carried out by one or a combination of the three modes: post-certification follow-up inspection, sampling testing or inspection on production site, and market sampling testing or inspection.



For Types C and D production enterprises: The post-certification supervision may be carried out as post-certification follow-up inspection and supervision sampling testing (either production site sampling or market sampling, or a combination thereof).



The certification modes for production enterprises of service components for discontinued-production vehicle models may be selected according to Annex 5.



CCAP will determine the certification mode(s) suitable for the certification client based on the characteristics of the product applied for certification, the production modes, and the principles of certification risk control, in conjunction with the results of production enterprise classification management.



4 Certification unit division



In principle, the seat and seat headrest products for motor vehicles produced by the same producer (manufacturer) at the same production enterprise (site) that do not have significant differences in the following aspects constitute one certification unit:



(1) For seats and headrests to be considered in the same unit under GB 15083-2019:



① The structure, shape, dimensions, materials, and mass of the seats, allowing differences in seat trim cover material and color, and allowing a mass variation of up to 5% from the approved seat model;



② The types and dimensions of the adjustment, displacement and locking systems for the seats, seat backrests, and their components;



③ The types and dimensions of the seat anchorages;



④ The dimensions, frame, material, and padding of the headrests, allowing differences in trim cover material and color;



⑤ The types and dimensions of headrest accessories, and if the headrest is a separate type, the characteristics of the component to which the headrest is attached is also included.



(2) For the seats for passenger vehicles to be considered in the same unit under GB 13057-2023:



① The specification, model, and production enterprise of the seats are the same;



② The structure, material, shape, and dimensions of the load-bearing components of the seats are the same;



③ The structural types and models of the adjustment, locking and displacement systems of the seats are the same;



④ The structure, material, and dimensions of the seat attachments and accessories are the same;



⑤ The configuration, type, securing method, and production enterprise of the safety-belts on the seats are the same.



(3) For the seats for school buses to be considered in the same unit under GB 24406-2024:



① The type, specification, and production enterprise of the seats are the same;



② The structure, material, shape, and dimensions of the load-bearing components of the seats are the same;



③ The structural types of the adjustment, locking and displacement systems of the seats are the same;



④ The structure, material, and dimensions of the seat attachments and accessories are the same;



⑤ The configuration, type, securing method, and production enterprise of the safety-belts on the seats are the same;



⑥ The G point height of the seat immediately behind it is the same, with a decrease or increase of no more than 72mm.



In principle, the certification client shall file the application for certification according to the unit division principles. Products of multiple "models (or specifications)” may be included in the same unit. Products of the same model refer to those that have no impact on conformity with the standards in terms of design.



For the same products produced by the same producer but at different production enterprises, or for products of the same model produced by different producers but at the same production enterprise, type test may be carried out on the samples of only one unit. For the products of other production enterprises/producers, the data for conformity verification shall be provided for such purpose.

1 Application scope
2 Certification standards
3 Selection of certification modes and related requirements
3.1 Basic certification mode
3.2 Applicability of certification modes
4 Certification unit division
5 Certification application
5.1 Submission and acceptance of certification application
5.2 Certification application data
5.3 Certification scheme and certification contract
6 Implementation of certification
6.1 Type test
6.2 Initial factory inspection
6.3 Certification evaluation and decision
6.4 Certification time limit
6.5 Service components of discontinued-production vehicle models
6.6 Special provisions for "issuing the certificate first and then inspecting the factory" within the same producer (manufacturer)
7 Post-certification supervision
7.1 Post-certification follow-up inspection
7.2 Sampling testing or inspection on production site
7.3 Market sampling testing or inspection
7.4 Frequency and time of post-certification supervision
7.5 Record of post-certification supervision
7.6 Evaluation of post-certification supervision results
8 Certification certificate
8.1 Maintenance of certification certificate
8.2 Contents of certification certificate
8.3 Change and extension of certification certificate
8.4 Cancellation, suspension and revocation of certification certificate
8.5 Use of certification certificate
9 Certification mark
10 Charges
11 Certification responsibilities
12 Process and timeline requirements related to technical disputes, complaints, and appeals
Annex 1 Description of seat and seat headrest products for motor vehicles
Annex 2 List of key components/materials for seat and seat headrest products for motor vehicles
Annex 3 CoP requirements
Appendix 1 Requirements for quality assurance capacity of factory
Annex 4 Requirements for the preparation of the CoP control plan and execution report
Appendix 1 Recommended format for CoP control plan
Appendix 2 Product COP testing and inspection plan
Annex 5 Implementation of certification of after-sales service spare parts for discontinued-production vehicle models
Annex 6 Principles of production enterprise classification
Annex 7 Requirements for testing by utilizing testing resources of production enterprises and utilization of other conformity assessment results

1 适用范围
本规则适用于M 类、N 类汽车的座椅及座椅头枕产品。但不适用于下述座椅及头枕：
（1） 后向座椅及其在这些座椅上安装的头枕；
（2） 儿童乘员使用的座椅或约束系统；
（3） 客车和卡车的卧铺；
（4） 构成座椅总成的零部件，如座椅骨架、座椅护面等；
（5） 构成头枕总成的零件，如头枕骨架、头枕护面等。
由于法律法规或相关产品标准、技术、产业政策等因素发生变化所引起的适用范围调 整，应以CCAP发布的公告为准。
2 认证依据标准

GB 15083-2019 汽车座椅、座椅固定装置及头枕强度要求和试验方法
GB 13057-2023 客车座椅及其车辆固定件的强度
GB 24406-2024 专用校车学生座椅及其车辆固定件的强度
GB 8410-2006 汽车内饰材料的燃烧特性 GB 38262-2019 客车内饰材料的燃烧特性
生产企业应全面执行国家颁布的汽车座椅及座椅头枕产品相关的法律、法规及标准的 强制性要求，且符合要求。
上述标准原则上应执行国家标准化行政主管部门发布的最新版本。当需使用标准的其 他版本时，则应按CCAP发布的适用相关标准要求的公告执行。
3 认证模式的选择及相关要求
3.1 基本认证模式
实施汽车座椅及座椅头枕产品CCAP标志认证的基本认证模式为： 型式试验 + 初始工厂检查 + 获证后监督
基本认证模式是以生产企业诚信自律、有效管理、稳定生产为前提，基于产品的固有 安全风险特点和生产企业普遍采用的生产工艺确定的认证模式。
获证后监督是指CCAP对获证产品及其生产企业实施的监督，监督方式为获证后的跟 踪工厂检查、生产现场抽取样品检测或检查、市场抽样检测或者检查三种方式之一或各种 组合。

3.2 认证模式的适用性
CCAP将按照生产企业分类原则，针对不同类别的企业，在基本认证模式的基础上酌 情增加/减少认证要素进行组合，包括：
A类、B类生产企业：获证后监督可采用获证后的跟踪检查、生产现场抽取样品检测或 者检查、市场抽样检测或者检查三种方式之一或者组合。
C类、D类生产企业：获证后监督应采用获证后的跟踪检查和监督抽样检测（生产现场 抽样或市场抽样的之一或者组合）。
已停产车型维修部件产品生产企业的认证模式选择可根据附件5进行。
CCAP根据申请认证产品特点、生产方式及认证风险控制原则，结合生产企业分类管 理结果，以确定认证委托人所能适用的认证模式。
4 认证单元划分
原则上，同一生产者（制造商）、同一生产企业（场所）生产的在以下方面没有显著 差异的汽车座椅及座椅头枕产品为一个认证单元：
（1） 适用GB 15083-2019标准的座椅及头枕同一单元的要求：
1 座椅的结构、形状、尺寸、材料及质量，允许座椅蒙皮材料和颜色不同；允许 与已被批准座椅型式的座椅质量有5％范围内的差异；
2 座椅、座椅靠背及其组成部件的调节装置、移位装置及锁止装置的型式和尺寸；
3 座椅固定装置的型式和尺寸；
4 头枕的尺寸、构架、材料和衬垫，允许其蒙皮材料和颜色不同；
5 头枕附件的型式和尺寸，若头枕为分体式头枕，还包括头枕连接部件的特性。
（2） 适用GB 13057-2023标准的客车座椅同一单元的要求：
1 座椅的规格型号、生产企业相同;
2 座椅的承载件的结构、材料、形状、尺寸相同;
3 座椅的调节装置、锁止装置、移位装置的结构型式、型号相同:
4 座椅连接件和附件的结构、材料、尺寸相同;
5 座椅上的安全带的配置、型式、固定方式、生产企业相同；
（3） 适用GB 24406-2024标准的校车座椅同一单元的要求：
1 座椅的类型、规格、生产企业相同;
2 座椅的承载件的结构、材料、形状、尺寸相同;
3 座椅的调节装置、锁止装置、移位装置的结构型式相同;
4 座椅连接件和附件的结构、材料、尺寸相同;

5 座椅上的安全带的配置、型式、固定方式、生产企业相同:
6 紧邻其后的座椅的 G点高度相同、减小或增大不超过 72 mm。
原则上，认证委托人应依据单元划分原则提出认证委托。同一单元中可包含多个“ 型 号（或规格） ”的产品。同一型号是指在设计上对标准符合性没有影响的产品。
相同生产者、不同生产企业生产的相同产品，或不同生产者、相同生产企业生产的相 同型号产品，可考虑仅在一个单元的样品上进行型式试验，其他生产企业/生产者的产品需 提供资料进行一致性核查。
5 认证委托
5.1 认证委托的提出与受理
认证委托人需根据CCAP的认证流程和要求以适当的方式向CCAP提出认证委托，并对 提交认证申请资料的真实性和合法性负责。认证委托人应能够承担相关质量及法律责任。
委托认证的汽车座椅及座椅头枕产品生产者（制造商）和生产企业应能正常生产，并 符合国家法律法规及相关产业政策要求。生产者（制造商）应符合CNCA-00C-008《强制 性产品认证实施规则 自我声明》对生产者（制造商）的规定，即应是对产品质量负主体 责任并具有独立法人资格的企业。
CCAP将对认证委托人提交的认证委托资料进行完整性和规范性审查，如审查过程中 发现存在问题，CCAP受理人员将与认证委托人沟通，要求认证委托人对认证委托资料补 充完善后重新提交。资料审查合格予以受理的，CCAP将向认证委托人发出受理通知，并 与委托人签订认证合同。资料审查不合格不予受理的，CCAP将向认证委托人发出不予受 理通知，并明确告知不予受理原因。
有下列情形之一的不予受理：
（1）不符合国家产业政策；
（2）认证委托人、生产者（制造商）、生产企业的注册证明材料中，经营范围未覆 盖认证产品；法律证明材料缺失；
（3）列入国家信用信息严重失信主体相关名录。
（4）其他法律法规规定不得受理的情形。
5.2 认证委托资料
认证委托人应按照以下要求提供认证委托所需资料。
（1）认证委托人、生产者（制造商）、生产企业（工厂）基本信息
1）认证申请书；