![]() |
中标分类
行业分类
ICS分类
最新标准
|
登录注册 |
您的位置: 标准明细 |
GB/T 7725:2022 Room air conditioner English 1 Scope This document specifies the terms and definitions, product classification, technical requirements, tests, inspection rules, marking, packaging, transportation and storage of room air conditioners. This document is applicable to room air conditioners (free-air supply) for domestic indoor comfort and similar purposes, equipped with air-cooled and water-cooled condensers, fully enclosed motor-compressor, with a rated cooling capacity of less than 14,000W (hereinafter referred to as "air conditioner"), and ducted air conditioners with a rated cooling capacity of less than 8kW and an external static pressure of less than 25Pa. This standard is not applicable to the following products and systems: ——mobile air conditioners; ——individual assemblies not constituting a complete refrigeration system; ——equipment using the absorption refrigeration cycle; ——other ducted air conditioners. 2 Normative references The following documents contain requirements which, through reference in this text, constitute indispensable requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies. GB/T 191 Packaging - Pictorial marking for handling of goods GB/T 1766 Paints and varnishes - Rating schemes of degradation of coats (ISO 4628:2003, NEQ) GB/T 2423.3 Environmental testing - Part 2: Testing method - Test Cab: Damp heat, steady state (GB/T 2423.3-2016, IEC 60068-2-78:2012, IDT) GB/T 2423.17 Environmental testing for electric and electronic products - Part 2: Test methods - Test Ka: Salt mist (GB/T 2423.17-2008, IEC 60068-2-11:1981, IDT) GB/T 2828.1 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (GB/T 2828.1-2012, ISO 2859-1:1999, IDT) GB/T 2829 Sampling procedures and tables for periodic inspection by attributes (apply to inspection of process stability) GB/T 4214.1 Test method for noise of household and similar electrical appliances - General requirements (GB/T 4214.1-2017, IEC 60704-1:2010, MOD) GB/T 4798.1 Classification of environmental conditions - classification of groups of environmental parameters and their severities - Part 1: Storage (GB/T 4798.1-2005, IEC 60721-3-1:1997, MOD) GB/T 5296.2 Instructions for use of products of consumer interest - Part 2: Household and similar electrical appliances GB/T 9286 Paints and varnishes - Cross cut test for films (GB/T 9286-2021, ISO 2409:2020, IDT) GB/T 14522 Artificial weathering test method for plastics, coating and rubber materials used for machinery industrial products - Fluorescent UV lamps GB 21455-2019 The minimum allowable value of the energy efficiency and energy efficiency grades for room air conditioners GB/T 22939.7 Package of household and similar electrical appliances - Particular requirements for refrigerator JB/T 10359 Environmental technical requirements of the plastics for the outdoor units for air conditioners IEC 60335-2-40:2018 Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers 3 Terms, definitions and symbols 3.1 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 room air conditioner device for supplying treated air to a room Note: It mainly includes a refrigeration system for cooling and dehumidification, an air circulation and purification device, and also means for heating and ventilation (such equipment can be provided in more than one assembly, the separated assemblies (split-systems) of which are intended to be used together). 3.1.2 heat pump refrigeration system that heats up indoor air by changing the flow direction of refrigerant in the refrigeration system, absorbing heat from outdoor low-temperature air and releasing heat to indoor air Note: Air conditioners with heat pump heating capacity are called heat pump air conditioners. 3.1.3 supplementary electrical heating devices electric heating device used together with a heat pump 3.1.4 cooling capacity total capacity of heat removed from an indoor area per unit time when the air conditioner is in cooling operation under specified working conditions Note: It is expressed in watts (W). The rated values of cooling capacity include rated intermediate cooling capacity, rated intermediate cooling capacity, rated maximum cooling capacity and rated minimum cooling capacity. Among them, the rated intermediate cooling capacity is 50% of the rated cooling capacity ±100W. 3.1.5 cooling power input power input of the air conditioner in the cooling capacity test. Note: It is expressed in watts (W). The rated values of cooling power input include rated cooling power input and rated intermediate cooling power input. 3.1.6 heating capacity total capacity of heat supplied to an indoor room per unit time when the air conditioner is heating operation under specified working conditions Note 1: It is expressed in watts (W). The rated values of heating capacity include rated heating capacity, rated intermediate heating capacity, rated maximum heating capacity, rated minimum heating capacity and rated low-temperature heating capacity. Among them, the rated intermediate heating capacity is 50% of the rated heating capacity ±100W. Note 2: The heating capacity is only the heating capacity of heat pumps, excluding the heating capacity of supplementary electrical heating devices. 3.1.7 heating power input power input of the air conditioner in the heating capacity test Note: It is expressed in watts (W). The rated values of heating power input include rated heating power input and rated intermediate cooling power input and rated low-temperature heating power input. 3.1.8 effective power input average electrical power input to the equipment in the required time obtained from: a) the power input from the compressor(s); b) the power input to electric heating devices used only for defrosting; c) the power input to all control and safety devices of the equipment; and d) the power input for operation of all heat exchange/transfer devices (e.g. fans and pumps). Note: It is expressed in watts (W). Effective power input exclude input power of auxiliary electric heating devices. 3.1.9 energy efficiency ratio EER ratio of cooling capacity to effective power input when the air conditioner is refrigerating in any given working conditions and requirements. Note: It is expressed in watts per watt (W/W). 3.1.10 coefficient of performance COP ratio of heating capacity to effective power input when the air conditioner is heating in any given working conditions and requirements Note: It is expressed in watts per watt (W/W). 3.1.11 standard air air with atmospheric pressure of 101.325kPa, temperature of 20℃, and density of 1.204kg/m3 3.1.12 indoor discharge air-flow supply air volume of room air flow supplied by the air conditioner indoor unit to the room or space per unit time when the air conditioner is operating in the required conditions and the ventilation and exhaust vents (if any) for indoor and outdoor air exchange are completely closed Note: It is expressed in m3/s or m3/h. 3.1.13 room-type calorimeter test device consisting of two adjacent chambers with partition walls in its middle. An chamber used as the indoor side and the other as the outdoor side, each of which is equipped with air conditioning equipment; its cooling capacity, heating capacity and water quantity can be measured and controlled, and used to balance the cooling capacity and dehumidification capacity on the indoor side and the humidification capacity and heating capacity on the outdoor side of the air conditioner to be tested. 3.1.14 air-enthalpy test method test method for cooling or heating capacity of the air conditioner, by which, the air supply parameters, the return air parameters and the indoor discharge air-flow of the air conditioner are measured; the capacity of the air conditioner is determined based on the product of the measured air volume and the difference between the enthalpy of air supply and that of return air 3.1.15 variable speed room air conditioner air conditioner, the speed of whose compressor can change within a certain range according to the size of heat load when the air conditioner is running 3.1.16 fixed speed room air conditioner air conditioner, the speed of whose compressor cannot change according to the size of heat load when the air conditioner is running 3.1.17 variable capacity room air conditioner air conditioner, the speed of whose compressor cannot change but the effective volume air delivery capacity (mass flow of refrigerant) changes within a certain range according to the size of heat load when the air conditioner is running 3.1.18 latent cooling capacity latent heat removed from a specific space by the air conditioner in a certain time period Note: It is expressed in watts (W). 3.1.19 sensible cooling capacity sensible heat removed from a specific space by the air conditioner in a certain time period Note: It is expressed in watts (W). 3.1.20 sensible heat ratio; SHR ratio of sensible cooling capacity to total cooling capacity 3.1.21 full-load operation air conditioners and controllers operate at the maximum continuous capacity specified by the manufacturer Note: All indoor units and compressor operate during full-load operation unless the indoor units and compressor are controlled by the automatic controller of the air conditioner. 3.1.22 multi-split room air conditioner device for supplying treated air to several rooms Note: It is a combined system mainly consisting of one outdoor set and more than one indoor sets, which enables multiple indoor sets to work at the same time, some indoor sets to work at the same time or single indoor set to work. 3.1.23 standby mode when connected to the main power, the air conditioner provides one or more of the following user-oriented functions or protection functions, which is a continuous mode for any product: ——other modes can be triggered by triggering remote switches (including remote control), internal sensors and timers; ——information or status displays including clocks; ——sensor-based functions. Note: In this mode, the protective devices like crankcase heater do not work. 3.1.24 cooling load factor CLF ratio of the heat load removed from the room during intermittent operation of room air conditioner by ON and OFF operations within the period formed by ON and OFF time to that removed from the room during continuous operation within the equal period 3.1.25 heating load factor HLF ratio of the heat load delivered into the room during intermittent operation of room air conditioner by ON and OFF operations within the period formed by ON and OFF time to that delivered into the room during continuous operation within the equal period 3.1.26 part load factor PLF ratio of energy efficiency of air conditioner in intermittent operation to that in continuous operation under the same temperature and humidity conditions 3.1.27 degradation coefficient CD coefficient of efficiency reduction of air conditioner due to intermittent operation 3.1.28 seasonal energy efficiency ratio SEER ratio of the total heat load removed from the room to the total power consumed when the air conditioner is in cooling operation in cooling seasons 3.1.29 heating seasonal performance factor HSPF ratio of the total heat load delivered into the room to the total power consumed when the air conditioner is in heating operation in heating seasons 3.1.30 annual performance factor APF ratio of the sum of the cool load removed from the indoor air and the heat load delivered into the room to the total power consumed during the same period in cooling and heating seasons 3.1.31 cooling seasonal total energy CSTE total power consumed by the air conditioner during cooling operation in cooling seasons Note: It is expressed in watt hour (W•h). 3.1.32 heating seasonal total energy HSTE total power consumed by the air conditioner during heating operation in heating seasons Note: It is expressed in watt hour (W•h). 3.1.33 annual power consumption APC sum of the cooling seasonal total energy and the heating seasonal total energy Note: It is expressed in watt hour (W•h). 3.1.34 cooling load intersection point of the perpendicular line passing through the temperature point and the cooling load line which is as the straight line connecting the zero load at 23℃ and the point where cooling capacity at an outdoor temperature of 35℃ is taken as the cooling building load 3.1.35 heating load it is evaluated in the room with the same size as that for cooling load evaluation, and the fixed ratio of the cooling load is calculated .... ... 3.2 Symbols 3.2.1 General symbols For the purposes of this document, the following symbols apply. An area, nozzle m2 Cd nozzle discharge coefficient — cpa1 specific heat of moist air entering indoor-side J/(kg•℃) cpa2 specific heat of moist air leaving indoor-side J/(kg•℃) cpa3 specific heat of moist air entering outdoor-side J/(kg•℃) cpa4 specific heat of moist air leaving outdoor-side J/(kg•℃) Dn nozzle throat diameter m Dt outer diameter of heat exchange tube m ha1 specific enthalpy of air entering indoor-side J/kg (dry air) ha2 specific enthalpy of air leaving indoor-side J/kg (dry air) hr1 specific enthalpy of refrigerant entering indoor-side J/kg hr2 specific enthalpy of refrigerant leaving indoor-side J/kg hw1 enthalpy of water or steam used for humidification, if no water supply is supplied to humidifier during the test, then hw1 take the enthalpy value under the water temperature in the humidifier in the reprocessing unit kJ/kg hw2 enthalpy of condensed water discharged from indoor side to outdoor side, when the temperature of condensed water cannot be measured (usually occurring inside the air conditioner), the condensate temperature can be instead of or usually assumed to be equal to the wet-bulb temperature estimation of the conditioner air supply kJ/kg hw3 enthalpy of condensed water discharged from outdoor-side reprocessing unit at temperature leaving calorimeter chamber kJ/kg hw4 enthalpy of the water supplied to the outdoor side chamber kJ/kg hw5 enthalpy of the condensed water (high temperature condition), or the frost (low temperature or ultra-low temperature condition) kJ/kg K1 2.5004×106 (latent heat of vaporization of water at 0℃) J/kg L length of heat exchange tube m Lpi a weighted sound pressure level at point i of ejector outdoor unit in the noise test dB(A) N total number of noise measuring points of ejector outdoor unit, N=4 — Pi total power input to indoor side (such as electric heating power of lighting and auxiliary devices, balance heat of humidifying devices, etc.) W Pk power input to compressor W Po total power input to outdoor side (except power input to air conditioner) W Pr power input to electric heater W Pt total power input to air conditioner W pn atmospheric pressure at nozzle throat Pa pv velocity pressure at nozzle throat or static pressure difference across nozzle Pa qmo measured value of air volume flow rate, outdoor-side m3/s qro refrigerant and oil mixture flow rate m3/s qs standard air flow kg/s qvi air volume flow rate, indoor-side m3/s qwc rate at which water vapour is condensed by the equipment g/s qwo water mass flow supplied to the outside test chamber for maintaining the test conditions g/s R1 thermal resistance of thermal insulation layer outside the heat exchange tube (m•℃)/W R2 heat transfer resistance between insulation layer and air (m•℃)/W SHR sensible heat ratio — T thickness of insulation layer m ta1 temperature of air entering indoor-side ℃ ta2 temperature of air leaving indoor-side ℃ ta3 temperature of air entering outdoor-side ℃ ta4 temperature of air leaving outdoor-side ℃ va average velocity of air, at nozzle m/s ν'n specific volume of air-water vapour mixture at nozzle m3/kg Foreword i 1 Scope 2 Normative references 3 Terms, definitions and symbols 4 Product classification 5 Technical requirements 6 Tests 7 Inspection rules 8 Marking, packaging, transport and storage Annex A (Normative) Multi-split room air conditioner Annex B (Normative) Calculation of seasonal performance factor of room air conditioner Annex C (Informative) Occurrence time of each temperature calculated with meteorological data of a typical city (taking Nanjing as an example) Annex D (Normative) Tests and calculation methods of cooling capacity and heating capacity Annex E (Informative) Measuring instruments Annex F (Informative) Air-flow measurement Annex G (Informative) Cooling condensate measurements Annex H (Informative) Pictorial examples of the heating capacity test procedures given in D.4 Annex I (Normative) Determination of noise Annex J (Normative) Test of standby power Annex K (Informative) Classification of some performance Annex L (Informative) Test method for temperature control fluctuation Annex M (Informative) Refrigerant enthalpy test method Annex N (Informative) Outdoor air-enthalpy test method Annex O (Informative) Indoor calorimeter confirmative test method Annex P (Informative) Outdoor calorimeter confirmative test method Annex Q (Informative) Balanced-type calorimeter confirmative test method Bibliography 房间空气调节器 1 范围 本文件规定了房间空气调节器的术语和定义、产品分类、技术要求、试验、检验规则、标志、包装、运输和贮存。 本文件适用于采用风冷及水冷冷凝器、全封闭型电动机-压缩机,额定制冷量14 000 W以下以创造室内舒适环境为目的的家用和类似用途的自由送风型房间空气调节器(以下简称空调器),以及额定制冷量8 kW以下且外部静压小于25 Pa的风管式空调器。 本文件不适用于以下产品及系统: ——移动式空调器; ——单独组件,不能组成完整的制冷系统; ——采用吸收制冷循环的空调器; ——其他的风管式空调器。 2 规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中,注日期的引用文件,仅该日期对应的版本适用于本文件;不注日期的引用文件,其最新版本(包括所有的修改单)适用于本文件。 GB/T 191 包装储运图示标志 GB/T 1766 色漆和清漆 涂层老化的评级方法(ISO 4628:2003,NEQ) GB/T 2423.3 环境试验 第2部分:试验方法 试验Cab:恒定湿热试验(GB/T 2423.3-2016,IEC 60068-2-78;2012,IDT) GB/T 2423.17 电工电子产品环境试验 第2部分:试验方法 试验Ka:盐雾(GB/T 2423.17-2008,IEC 60068-2-11:1981,IDT) GB/T 2828.1 计数抽样检验程序 第1部分:按接收质量限(AQL)检索的逐批检验抽样计划(GB/T 2828.1-2012,ISO 2859-1:1999,IDT) GB/T 2829 周期检验计数抽样程序及表(适用于对过程稳定性的检验) GB/T 4214.1 家用和类似用途电器噪声测试方法 通用要求(GB/T 4214.1-2017,IEC 60704-1:2010,MOD) GB/T 4798.1 环境条件分类 环境参数组分类及其严酷程度分级 第1部分:贮存(GB/T 4798.1-2005,IEC 60721-3-1:1997,MOD) GB/T 5296.2 消费品使用说明 第2部分:家用和类似用途电器 GB/T 9286 色漆和清漆 划格试验(GB/T 9286-2021,ISO 24092020,IDT) GB/T 14522 机械工业产品用塑料、涂料、橡胶材料人工气候老化试验方法 荧光紫外灯 GB 21455-2019 房间空气调节器能效限定值及能效等级 GB/T 22939.7 家用和类似用途电器包装 空调器的特殊要求 JB/T 10359 空调器室外机用塑料 环境技术要求 IEC 60335-2-40:2018 家用和类似用途电器 安全 第2-40部分:电热泵、空调和除湿器的特殊要求(Household and similar electrical appliances—Safety—Part 2-40:Particular requirements for electrical heat pumps,air-conditioners and dehumidifiers) 3 术语和定义、符号 3.1 术语和定义 下列术语和定义适用于本文件。 3.1.1 房间空气调节器 room air conditioner 一种向室内提供经过处理的空气的设备。 注:主要包括制冷和除湿用的制冷系统、空气循环和净化装置,还可包括加热和通风装置等(它们可被组装在一个箱壳内或被设计成一起使用的组件系统)。 3.1.2 热泵 heat pump 通过转换制冷系统制冷剂运行流向,从室外低温空气吸热并向室内放热,使室内空气升温的制冷系统。 注:具有热泵制热能力的空调器称为热泵型空调器。 3.1.3 辅助电热装置 supplementary electrical heating devices 与热泵一起使用进行制热的电热装置。 3.1.4 制冷量 cooling capacity 空调器在任何给定的工况和条件下制冷运行时,单位时间内从室内除去的热量总和。 注:单位为瓦(W)。制冷量的额定值包括额定制冷量、额定中间制冷量、额定最大制冷量及额定最小制冷量。其中,额定中间制冷量在50%额定制冷量±100 W范围内。 3.1.5 制冷消耗功率 cooling power input 空调器进行制冷量试验时,所消耗的功率。 注:单位为瓦(W)。制冷消耗功率的额定值包括额定制冷消耗功率、额定中间制冷消耗功率。 3.1.6 制热量 heating capacity 空调器在任何给定的工况和条件下制热运行时,单位时间内送入室内的热量总和。 注1:单位为瓦(W)。制热量的额定值包括额定制热量、额定中间制热量、额定最大制热量、额定最小制热量及额定低温制热量。其中,额定中间制热量在50%额定制热量±100 W范围内。 注2:制热量仅为热泵制热量,不包含辅助电热装置的制热量。 3.1.7 制热消耗功率 heating power input 空调器在进行制热量试验时,所消耗的功率。 注:单位为瓦(W)。制热消耗功率的额定值包括额定制热消耗功率、额定中间制热消耗功率及额定低温制热消耗功率。 3.1.8 有效输入功率 effective power input 在规定时间内输入空调器内的平均电功率,包括: a) 压缩机运行的输入功率; b) 仅用于除霜的电热装置的输入功率; c) 所有控制和安全装置的输入功率; d) 热交换传输装置的输入功率(风扇、泵等)。 注:单位为瓦(W)。不包括辅助电热装置的输入功率。 3.1.9 能效比 energy efficiency ratio EER 在任何给定的工况和规定条件下,空调器进行制冷运行时,制冷量与有效输入功率之比。 注:单位为瓦每瓦(W/W)。 3.1.10 性能系数 coefficient of performance COP 在任何给定的工况和规定条件下,空调器进行制热运行时,制热量与有效输入功率之比。 注:单位为瓦每瓦(W/W)。 3.1.11 标准空气 standard air 大气压力为101.325 kPa,温度为20℃时,密度为1.204 kg/m3的干空气。 3.1.12 循环风量 indoor discharge air-flow 房间送风量 空调器用于室内、室外空气进行交换的通风门和排风门完全关闭(如果有)、并在规定条件下运行,单位时间内空调器室内机向房间或送风区域送入的风量。 注:单位为立方米每秒(m3/s)或立方米每小时(m3/h)。 3.1.13 房间型量热计 room-type calorimeter 由两间相邻、中间有隔墙的房间所组成的试验装置。一间作为室内侧,另一间作为室外侧,每间均装有空气调节设备;其冷量,热量及水量均可测量和控制,并用以平衡被测空调器在室内侧的制冷量和除湿量以及在室外侧的加湿量和加热量。 3.1.14 空气焓值法 air-enthalpy test method 一种测定空调器制冷量或制热量的试验方法,它对空调器的送风参数、回风参数以及循环风量进行测量,用测出的风量与送风、回风熔差的乘积确定空调器的能力。 3.1.15 转速可控型空调器 variable speed room air conditioner 空调器运行时,根据热负荷的大小,其压缩机的转速可在一定范围内发生变化的空调器。 3.1.16 转速一定型空调器 fixed speed room air conditioner 空调器运行时,压缩机的转速不随热负荷的大小而发生变化的空调器。 3.1.17 容量可控型空调器 variable capacity room air conditioner 空调器运行时,根据热负荷的大小,压缩机的转速不变,但其有效容积输气量(制冷剂质量流量)可在一定范围内发生变化的空调器。 3.1.18 潜冷量 latent cooling capacity 在一定的间隔时间里,空调器从特定空间移除的潜热。 注:单位为瓦(W)。 3.1.19 显冷量 sensible cooling capacity 在一定的间隔时间里,空调器从特定空间移除的显热。 注:单位为瓦(W)。 3.1.20 显热比 sensible heat ratio;SHR 显冷量和总制冷量之比。 3.1.21 全负荷运行 full-load operation 空调器和控制器在制造商规定的空调控制器允许的最大连续能力下运行。 注:在全负荷运行时,所有室内机和压缩机均工作,除非室内机和压缩机受控于空调器的自动控制器。 3.1.22 一拖多房间空气调节器 multi-split room air conditioner 一种向多个室内提供经过处理的空气的设备。 注:主要由一台室外机组与一台以上的室内机组相连接,可以实现多个室内机组同时工作、部分室内机组同时工作或单独室内机组工作的组合体系统,以下简称“一拖多空调器”。 3.1.23 待机模式 standby mode 空调器在连接到主电源时,提供以下一种或多种面向用户功能或保护功能,且为持续的任何产品模式; ——可以通过触发远程开关(包括远程控制)、内部传感器,定时器来触发其他模式; ——信息或包含时钟的状态显示; ——基于传感器的功能。 注:该模式下类似曲轴箱加热器等保护装置不工作。 3.1.24 制冷负荷系数 cooling load factor CLF 空调器制冷运行时,通过室内温度调节器的通(ON),断(OFF)使空调器进行断续运行时,ON时间与OFF时间构成的断续运行的1个周期内,从室内除去的热量和与此等周期时间内连续制冷运行时,从室内除去的热量之比。 3.1.25 制热负荷系数 heating load factor HLF 空调器制热运行时,通过室内温度调节器的通(ON)、断(OFF)使空调器进行断续运行时,由ON时间与OFF时间构成的断续运行的1个周期内,送入室内的热量和与此等周期时间内连续制热运行时,送入室内的热量之比。 3.1.26 部分负荷率 part load factor PLF 在同一温湿度条件下,空调器进行断续运行时的能源消耗效率与进行连续运行时的能源消耗效率之比。 3.1.27 效率降低系数 degradation coefficient CD 空调器因断续运行而发生效率降低的系数。 3.1.28 制冷季节能源消耗效率 seasonal energy efficiency ratio SEER 制冷季节期间,空调器进行制冷运行时从室内除去的热量总和与消耗电量的总和之比。 3.1.29 制热季节能源消耗效率 heating seasonal performance factor HSPF 制热季节期间,空调器进行制热运行时,送入室内的热量总和与消耗电量的总和之比。 3.1.30 全年能源消耗效率 annual performance factor APF 空调器在制冷季节和制热季节期间,从室内空气中除去的冷量与送入室内的热量的总和与同期间内消耗电量的总和之比。 3.1.31 制冷季节耗电量 cooling seasonal total energy CSTE 制冷季节期间,空调器进行制冷运转时所消耗的电量总和。 注:单位为瓦时(W·h)。 3.1.32 制热季节耗电量 heating seasonal total energy HSTE 制热季节期间,空调器进行制热运转时所消耗的电量总和。 注:单位为瓦时(W·h)。 3.1.33 全年运转时季节耗电量 annual power consumption APC 制冷季节时的制冷季节耗电量与制热季节时的制热季节耗电量之总和。 注:单位为瓦时(W·h)。 3.1.34 制冷负荷 cooling load 室外温度为35℃时的制冷量作为制冷建筑负荷,连接此点与23℃(0负荷点)的直线为制冷负荷线,过温度点的垂线与制冷负荷线的交点。 3.1.35 制热负荷 heating load 用与制冷负荷大小相同的房间来评价,并用对制冷负荷的固定比率进行计算。 注1。因住宅结构不同,制热负荷与制冷负荷的比率平均为1.25,制热负荷可用下面的公式算出:制热负荷=1.25×制冷负荷。 注2:室外温度0℃时的制热的负荷(制冷量×1.25×0.82),与室外温度17℃为0负荷的点连接的直线作为制热负荷线。 3.1.36 温控波动 temperature control fluctuation 在规定条件下,空调器进风口规定位置测得的温度波动值。 注:单位为摄氏度(℃)。 3.1.37 单工工作状态 one-unit operation 一拖多空调器室内机组中仅有一台室内机组与室外机组运行,其余室内机组处于停止使用的工作状态。 3.1.38 全工工作状态 all-unit operation 一拖多空调器室外机组与所有能同时启动的室内机组同时运行且处于使用的工作状态。 注1:如果一拖多空调器的室内机组与室外机组有多种组合配置,且存在多个全工工作状态(此状态的室内机组的制冷量总和不低于室外机组的制冷量)时,在各种组合配置的全工工作状态或选厂家推荐组合配置的一种全工工作状态下进行总能力试验。 注2:如果一拖多空调器的室内机组与室外机组有多种组合并且在最大能力组合运行时,仍有室内机组处于停止使用的工作状态(室内机组同时运行台数少于室内机组的总台数)时,在室内机组与室外机组最大组合能力工作状态运行即局部-全工工作状态下进行总能力试验。 3.1.39 低温制热能力率 low temperature heating capacity rate 在额定低温制热工况下的实测制热量与标称额定制冷量的比率。 注:以%表示。 3.1.40 最小噪声 lowest noise 分别在额定制冷工况和额定制热工况下,压缩机设定在最小制冷量和最小制热量对应的转速(转速可控型房间空调器),风量调至最低风速(风机风速可调),按照附录I的方法,测得的空调器噪声值。 注:单位为分贝[dB(A)]。 3.1.41 制冷运行除湿能力 dehumidify capacity at the cooling test condition 进行额定制冷量试验时,测得单位制冷量下的除湿量。 注:单位为千克每小时千瓦[kg/(h·kW)]。 3.2 符号 3.2.1 通用符号 下列符号适用于本文件。 An 喷嘴喉部的面积 平方米(m2) Ca 喷嘴的流量系数 — Cpa1 空调器室内侧回风空气质量定压热容 焦每千克摄氏度[J/(kg•℃)] Cpa2 空调器室内侧送风空气质量定压热容 焦每千克摄氏度[J/(kg·℃)] Cpa3 空调器室外侧回风空气质量定压热容 焦每千克摄氏度[J/(kg·℃)] Cpa4 空调器室外侧送风空气质量定压热容 焦每千克摄氏度[J/(kg•℃)] Dn 喷嘴喉部直径 米(m) Dt 换热管外径 米(m) ha1 空调器室内侧回风空气焓值 焦每千克干空气[J/kg(干)] ha2 空调器室内侧送风空气焓值 焦每千克干空气[J/kg(干)] hr1 进入空调器室内侧的制冷剂比焓 焦每千克(J/kg) hr2 离开空调器室内侧的制冷剂比焓 焦每千克(J/kg) hw1 加湿用的水或蒸汽的焓值,如试验过程中未曾向加湿器供水,则hw1取再处理机组中加湿器内水温下的焓值 千焦每千克(kJ/kg) hw2 从室内侧排到室外侧的空调器凝结水的焓值,凝结水的温度不能实现测试时(一般在空调器内部发生),可以冷凝温度代替或通常假定等于空调器送风的湿球温度估算 千焦每千克(kJ/kg) hw3 室外侧再处理机组排出的凝结水在离开量热计隔室的温度下的焓值 千焦每千克(kJ/kg) hw4 进入室外侧水的焓值 千焦每千克(kJ/kg) hw5 外侧凝结水的焓值(高温工况),或结霜的焓值(低温或超低温工况) 千焦每千克(kJ/kg) K1 2.500 4×106(此值为0℃时的蒸发潜热) 焦每千克(J/kg) L 换热管管长 米(m) Lpi 顶出风式室外机噪声测试第i点的A计权声压级 分贝[dB(A)] N 顶出风式室外机噪声测点总数,N=4 — Pi 室内侧的总输入功率(如照明、辅助装置的电热功率、加湿装置的平衡热等) 瓦(W) Pk 压缩机输入功率 瓦(w) Po 室外侧的总输入功率(空调器输人功率除外) 瓦(W) Pr 电加热器的输入功率 瓦(W) Pt 空调器的总输入功率 瓦(W) pn 喷嘴喉部大气压 帕(Pa) pv 喷嘴喉部动压或喷嘴前后的静压差 帕(Pa) qmo 空调器室外侧风量测量值 立方米每秒(m3/s) qro 制冷剂和油混合物的流量 立方米每秒(m3/s) qs 标准空气流量 千克每秒(kg/s) qvi 空调器室内测点的风量 立方米每秒(m3/s) qwe 设备冷凝水的质量流量 克每秒(g/s) qwo 为维持试验工况,进入室外侧隔室水的质量流量 克每秒(g/s) R1 热管外保温层热阻 米摄氏度每瓦[(m·℃)/W] R2 保温层与空气换热热阻 米摄氏度每瓦(m·℃)/W] SHR 显热比 — T 保温层厚度 米(m) ta1 空调器室内侧回风温度 摄氏度(℃) ta2 空调器室内侧送风温度 摄氏度(℃) ta3 空调器室外侧回风温度 摄氏度(℃) ta4 空调器室外侧送风温度 摄氏度(℃) va 喷嘴喉部平均流速 米每秒(m/s) ν'n 喷嘴进口处的湿空气比容 立方米每千克(m3/kg) W1 循环、混合器组件的净重 克(g) W3 装有制冷剂样品后循环、混合器组件的质量 克(g) W5 装有样品中油的循环、混合器组件的质量 克(g) Wi1 室内侧回风空气的绝对湿度 千克每千克干空气[kg/kg(干)] Wi2 室内侧送风空气的绝对湿度 千克每千克干空气[kg/kg(干)] Wr 空调器内的凝结水量,即为再处理机组中加湿器蒸发的水量 克每秒(g/s) wn 测点处空气湿度 千克每千克干空气[kg/kg(干)] Xo 从空调器内取出的循环的制冷剂和油的混合液样品的含油量 — xr 制冷剂与制冷剂和油混合物的质量比 — Y 膨胀系数 — φ100 通过墙、地板和天花板由室外侧向外的漏热量(不包括中间隔墙) 瓦(W) φ1ci 室内侧再处理机组中冷却盘管带走的热量 瓦(W) φ1i 通过墙、地板和天花板由室内侧向外的漏热量(不包括中间隔墙) 瓦(W) φ1p 由室外侧通过中间隔墙传到室内侧的漏热量,由标定试验确定(或平衡型量热计可根据计算确定) 瓦(W) φ'1p 通过中间隔墙,从室外侧漏出的热量,当隔墙暴露在室内侧的面积等于暴露在室外侧的面积时,φ'1p=φ1p 瓦(W) φ1r 除了中间墙外,从周围环境通过墙、地板和天花板传到室内侧的漏热量 瓦(W) φc 室外侧再处理机组中冷却盘管带走的热量 瓦(W) φci 室内侧再处理机组中冷却盘管带走的热量 瓦(W) φhi 室内侧测定的制热量 瓦(w) φho 室外侧测定的制热量 瓦(W) φ1ci 潜冷量 瓦(W) φt 由室内侧通过中间隔墙传入室外侧的漏热量 瓦(W) 由室内侧通过中间墙传入室外侧的漏热量,当隔墙暴露在室内侧的面积等于暴露在室外侧的面积时, 瓦(w) φr 电加热器的制热量 瓦(w) φsci 显冷量 瓦(W) φtci 室内侧测定的空调器总制冷量 瓦(W) φtco 室外侧测定的空调器总制冷量 瓦(W) μ 空气动力粘度 千克每米秒[kg/(m·s)] α 压力比 — αa 保温层与空气之间换热系数 瓦每米摄氏度[W/(m·℃)] λ 保温层的传热系数 瓦每米摄氏度[W/(m·℃)] 顶出风式室外机噪声测试测量表面平均A计权分声压级 贝[dB(A)] ∑Po 室外侧再加热器、风机等全部设备的总输入功率 瓦(W) ∑Pr 室内侧的总输入功率 瓦(W) ΔT 换热管内与环境之间的温差 摄氏度(℃) ΔTi(r=0) 数据收集期间前5 min进、出风温差的平均值 摄氏度(℃) ΔTi(r) 数据收集期间任一5 min进、出风温差的平均值 摄氏度(℃) %ΔT 数据收集期间任一5 min进、出风温差的改变 — 3.2.2 APF计算所用符号 下列符号适用于附录B。 APF 全年能源消耗效率 瓦时每瓦时[W·h/(W·h)] APC 全年运转时季节耗电量 瓦时(W·h) CD 效率降低系数,通常取CD=0.25 — CLF 制冷负荷系数,即φc(cyc)与φc(dry)的比值 — COPh(cyc) 空调器进行断续制热试验时的性能系数 瓦每瓦(W/W) COPext,f(tf) 空调器在温度tf时,在结霜区域,以最大制热能力运行时的性能系数 瓦每瓦(W/W) COPfe,f(tj) 制热温度tj时,结霜区域空调器在额定制热量和最大制热量之间运行时的性能系数 瓦每瓦(W/W) COPful(ta) 空调器在温度ta时,在非结霜区域,以额定制热能力运行时的性能系数 瓦每瓦(W/W) COPful(7) 空调器进行额定制热量试验时的性能系数 瓦每瓦(W/W) COPful,f(tg) 空调器在温度tg时,在结霜区域,以额定制热能力运行时的性能系数 瓦每瓦(W/W) COPhaf(td) 空调器在温度td时,在非结霜区域,以中间制热能力运行时的性能系数 瓦每瓦(W/W) COPhaf,f(te) 空调器在温度te时,在结霜区域,以中间制热能力运行时的性能系数 瓦每瓦(W/W) COPhf(tj) 制热温度tj时,无结霜区域空调器在中间制热量和额定制热量之间运行时性能系数 瓦每瓦(W/W) COPhf,f(tj) 制热温度tj时,结霜区域空调器在中间制热量和额定制热量之间运行时性能系数 瓦每瓦(W/W) COPmh,f(tj) 制热温度tj时,结霜区域空调器在25%额定制热量和中间制热量之间运行时性能系数 瓦每瓦(W/W) COPmin(tq) 空调器在温度tq时,在非结霜区域,以25%额定制热能力运行时的性能系数 瓦每瓦(W/W) COPmin,f(tr) 空调器在温度tr时,在结霜区域,以25%额定制热能力运行时的性能系数 瓦每瓦(W/W) CSTE 制冷季节耗电量 瓦时(W·h) CSTL 季节制冷量 瓦时(W·h) EERc(cyc) 空调器进行断续制冷试验时的能效比 瓦每瓦(W/W) EERc(cry) 空调器进行低湿制冷试验时的能效比 瓦每瓦(W/W) EERful(tb) 空调器在温度tb时,以额定能力运行时的能效比 瓦每瓦(W/W) EERhaf(tc) 空调器在温度tc时,以中间能力运行时的能效比 瓦每瓦(W/W) EERhf(tj) 空调器在温度tj时,在中间制冷能力和额定制冷能力之间对应房间热负荷运行时能效比的计算值 瓦每瓦(W/W) EERmh(tj) 空调器在温度tj时,在25%额定制冷量和中间制冷量之间对应房间热负荷运行时能效比的计算值 瓦每瓦(W/W) EERmin(tp) 空调器在温度tp时,以25%额定能力运行时的能效比 瓦每瓦(W/W) HLF 制热负荷系数,即φh(cyc)与如φful(7)的比值 — HSPF 制热季节能源消耗效率 瓦时每瓦时[W·h/(W·h)] HSTE 制热季节耗电量 瓦时(W·h) HSTL 季节制热量 瓦时(W·h) Lc(tj) 制冷工况下,温度tj时的房间热负荷 瓦(W) Lh(tj) 制热工况下,温度tj时的房间热负荷 瓦(W) nj 制冷季节中制冷的各温度下工作时间或制热季节中制热的各温度下工作时间 小时(h) Ph(cyc) 空调器进行断续制热试验时的实测制热消耗功率 瓦(W) Pc(cyc) 空调器进行断续制冷试验时的实测制冷消耗功率 瓦(W) Pc(dry) 空调器进行低湿制冷试验时的实测制冷消耗功率 瓦(W) Pful(tb) 空调器在tb时,以额定制冷能力运行时制冷消耗功率 瓦(W) Pful(tj) 温度tj时,空调器以额定制冷或制热能力运行所消耗的功率 瓦(W) Pful(-7) 空调器在室外温度-7℃时的额定制热消耗功率 瓦(W) Pful(7) 空调器进行额定制热量试验时的实测制热消耗功率 瓦(W) Pful(29) 空调器在室外温度29℃时的额定制冷消耗功率 瓦(W) Pful(35) 空调器进行额定制冷量试验时的制冷消耗功率 瓦(W) Pful,f(2) 空调器在额定低温制热工况时的消耗功率 瓦(W) Phaf(tc) 空调器在tc时,以中间制冷量运行的制冷消耗功率 瓦(W) Phaf(tj) 在温度tj时,制冷状态下空调器以中间能力运行时所消耗的功率或制热状态下无霜区域空调器以中间能力运行时所消耗的功率 瓦(W) Phf(tj) 制冷时温度tj时,空调器在中间制冷量与额定制冷量之间,对应房间热负荷的能力连续可变运行时所需消耗的功率 瓦(W) Pmh(tj) 制冷时温度为tj时,空调器25%额定制冷量与额定中间制冷量之间,对应房间热负荷的能力连续可变运行时所需消耗的功率 瓦(W) Pmin(tj) 在温度为tj时,制冷状态下空调器以25%额定能力运行时所消耗的功率或制热状态下无霜区域空调器以25%额定能力运行时所消耗的功率 瓦(W) Pmin(tp) 空调器在tp时,以25%额定制冷能力运行时的消耗功率 瓦(W) Pmin(tp) 空调器在tp时,在非结霜区域内,以25%额定制热能力运行的制热消耗功率 瓦(W) Pmin,f(tr) 空调器在tr时,在结霜区域内,以25%额定制热能力运行的制热消耗功率 瓦(W) PLF(tj) 温度tj时,空调器断续运行的部分负荷率 — PRH(tj) 空调器在温度tj时,空调器对应于房间负荷的制热量不足时,加入辅助电热装置的消耗功率,当φ(tj)≥Lh(tj)时,PRH(tj)=0 瓦(W) SEER 制冷季节能源消耗效率 瓦时每瓦时[W·h/(W·h)] X(tj) 温度tj时,房间热负荷与空调器制冷运行时的制冷量或制热运行时的制热量之比 — φh(cyc) 空调器进行断续制热试验时的实测制热量 瓦(W) φc(cyc) 空调器进行断续制热冷试验时的实测制冷量 瓦(W) φc(dry) 空调器进行低温制冷试验时的实测制冷量 瓦(W) φful(tb) 空调器在tb时,以额定制冷能力运行的制冷量 瓦(W) φful(tj) 空调器进行额定制冷量试验时的实测制冷量或进行额定制热量试验时的实测制热量 瓦(W) φful(-7) 空调器在室外温度-7℃时的额定超低温制热量 瓦(W) φful(7) 空调器进行额定制热量试验时的实测制热量 瓦(W) φful(29) 空调器在室外温度29℃时的额定制冷量 瓦(W) φful(35) 空调器进行额定制冷量试验时的实测制冷量 瓦(W) φful,f(tj) 结霜区域,温度tj时,空调器运行的制热量 瓦(W) φful,f(2) 空调器在额定低温制热工况时的制热量 瓦(W) φhaf(tc) 空调器在tc时,以中间制冷能力运行的制冷量 瓦(W) φhaf(tj) 温度tj时,制冷运行状态下空调器以中间能力运行时的制冷量或制热运行状态下无结霜区域空调器以中间能力运行时制热量 瓦(W) φhaf,f(tj) 制热温度tj时,结霜区域空调器以中间制热能力运行时制热量 瓦(W) φmh(tj) 制热温度tj时,在无结霜区域内,空调器在25%额定制热能力和中间制热能力之间运行时的制热量 瓦(W) φmin(tj) 在温度tj时,无制冷状态下空调器以25%额定制冷能力运行时的制冷量或制热状态下结霜区域空调器以25%额定制热能力运行时的制热量 瓦(W) φmin(tp) 空调器在tp时,以25%额定制冷能力运行的制冷量 瓦(W) φmin(tq) 空调器在tq时,在非结霜区域内,以25%额定制热能力运行的制热量 瓦(W) φmin,f(tj) 制热温度tj时,在结霜区域,空调器以25%%额定制热能力运行时的制热量 瓦(W) φmim,f(tr) 空调器在tr时,在结霜区域内,以25%额定制热能力运行的制热量 瓦(W) 4 产品分类 4.1 型式 4.1.1 空调器按使用气候环境分为: 气候类型 T1 T2 T3 气候环境 温带气候 低温气候 高温气候 最高温度 43℃ 35℃ 52℃ 4.1.2 空调器按结构形式分为。 a) 整体式,其代号C;整体式空调器结构分类为窗式(其代号省略)穿墙式,其代号为C。 b) 分体式,其代号F;分体式空调器分为室内机组和室外机组。室内机组结构分类为吊顶式、挂壁式、落地式、嵌入式、风管式等,其代号分别为D、G、L、Q、F等,室外机组代号为W。 c) 一拖多空调器,按照附录A。 4.1.3 空调器按主要功能分为: a) 单冷型,其代号省略(制冷专用); b) 热泵型,其代号R(包括制冷、热泵制热,制冷、热泵与辅助电热装置一起制热)。 4.1.4 空调器按冷却方式分为: a) 风冷式,其代号省略; b) 水冷式,其代号S。 4.1.5 空调器按压缩机控制方式分为: a) 转速一定(频率、转速、容量不变)型,其代号省略; b) 转速可控(频率、转速、容量可变)型,其代号Bp; c) 容量可控(容量可变)型,简称变容型,其代号Br。 4.2 基本参数 4.2.1 空调器的额定制冷量(单位为kW)优先选用系列为: 1.4、1.6、1.8、2.0、2.2、2.5、2.8、3.2、3.6、 4.0、4.5、5.0、5.6、6.3、7.1、8.0、9.0、10.0、 11.2、12.5、14.0。 4.2.2 空调器的额定制热量(单位为kW)优先选用系列为: 1.6、1.8、2.0、2.2、2.5、2.8、3.0、3.2、3.4、 3.6、3.8、4.0、4.2、4.5、4.8、5.0、5.3、5.6、 6.0、6.3、6.7、7.1、7.5、8.0、8.5、9.0、9.5、 10.0、10.6、11.2、11.8、12.5、13 .2、14.0、15.0、16.0。 4.2.3 空调器通常工作的环境温度如表1所示。 表1 空调器通常工作的环境温度 空调器型式 气候类型 T1 T2 T3 冷风型 18℃~43℃ 10℃~35℃ 21℃~52℃ 热泵型 -7℃~43℃ -7℃~35℃ -7℃~52℃ 注1:不带除霜装置的热泵型空调器,最低工作温度可为5℃。 注2:对于制造商声称用于表1更严酷环境的空调器,试验可按其声称的温度条件执行。 4.2.4 电源额定频率50 Hz,单相交流额定电压220 V或三相交流额定电压380 V,特殊要求不受此限。 4.3 型号命名 4.3.1 产品型号及含义如下: 工厂设计序号和(或)特殊功能代号等,允许用汉语拼音字母和(或)阿拉伯数字表示 —拖多产品代号(用阿拉伯数字表示,—拖三以上允许用“d”表示,一拖一代号省略) 室外机组结构代号 整体式结构分类代号或分体式室内机组结构分类代号 规格代号:(额定制冷量,用阿拉伯数字表示,其值取制冷量百位数或百位以上数) 冷却方式代号(风冷代号省略) 功能代号 结构形式代号 气候类型代号(T1型代号省略) 产品代号(房间空气调节器) 4.3.2 型号示例如下: 示例1:KT3C-35/A,表示T3气候类型、整体(窗式)冷风型房间空气调节器,额定制冷量为3 500 W,第一次改型设计。 示例2:KFR-28GW,表示T1气候类型、分体热泵型挂壁式房间空气调节器(包括室内机组和室外机组),额定制冷量为2800 W。 示例3:室内机组KFR-28G,表示T1气候类型、分体热泵型挂壁式房间空气调节器室内机组,额定制冷量为2 800 W。 示例4:室外机组KFR-28W,表示T1气候类型、分体热泵型房间空气调节器室外机组,额定制冷量为2 800 W。 示例5:KFR-50LW/Bp,表示T1气候类型,分体热泵型落地式转速可控型房间空气调节器(包括室内机组和室外机组),额定制冷量为5 000 W。 示例6:室内机组KFR-50L/Bp,表示T1气候类型、分体热泵型落地式转速可控型房间空气调节器室内机组,额定制冷量为5 000 W。 示例7:室外机组KFR-50W/Bp,表示T1气候类型,分体热泵型转速可控型房间空气调节器室外机组,额定制冷量为5 000 W。 注:额定制冷量百位以下数字不为零的空调器,其规格代号取百位或百位以上数字。例如:额定制冷量为3 350 W的T1气候类型、分体热泵型挂壁式房间空气调节器,其型号为KFR-33GW。 5 技术要求 5.1 通用要求 5.1.1 空调器应符合本文件以及其他相关强制性国家标准的规定,并应依据经规定程序批准的图样和技术文件设计制造。 5.1.2 热泵型空调器的额定(高温)制热量应不低于其额定制冷量,对于额定制冷量不大于7.1 kW的分体式热泵型空调器,其额定(高温)制热量应不低于其额定制冷量的1.1倍。 5.1.3 空调器的构件和材料应符合以下要求: a) 空调器的构件和材料的镀层和涂层外观应良好,室外部分应有适于使用环境的良好耐候性能; b) 空调器的保温层应有良好的保温性能和阻燃性、且无毒无异味; c) 空调器制冷系统受压零部件的材料应能在制冷剂、润滑油及其混合物的作用下,不产生劣化且保证整机正常工作。 |
联系我们
|
微信联系客服
![]() |
关于我们 | 联系我们 | 收费付款 |
服务热线:400-001-5431 | 电话:010-8572 5110 | 传真:010-8581 9515 | Email: bz@bzfyw.com | |
版权所有: 北京悦尔信息技术有限公司 2008-2020 京ICP备17065875号-1 |
本页关键词: |
GB/T 7725-2022, GB 7725-2022, GBT 7725-2022, GB/T7725-2022, GB/T 7725, GB/T7725, GB7725-2022, GB 7725, GB7725, GBT7725-2022, GBT 7725, GBT7725 |