GB/T 43018.5-2025 Interconnection and interoperation for textile equipment―Part 5：Nonwovens English, Anglais, Englisch, Inglés, えいご
This is a draft translation for reference among interesting stakeholders. The finalized translation (passing through draft translation, self-check, revision and verification) will be delivered upon being ordered.
ICS 59.120.02
CCS W 90
National Standard of the People's Republic of China
GB/T 43018.5-2025
Interconnection and interoperation for textile equipment - Part 5: Nonwovens
纺织装备互联互通与互操作 第5部分：非织造
(English Translation)
Issue date: 2025⁃02⁃28 Implementation date: 2025⁃09⁃01
Issued by the State Administration for Market Regulation
the Standardization Administration of the People's Republic of China
Contents
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviations
5 Architecture
6 Basic requirements
7 Information model
8 Data dictionary
Bibliography
Interconnection and interoperation for textile equipment - Part 5: Nonwovens
1 Scope
This document specifies the architecture, basic requirements, information model and data dictionary of non-woven equipment interconnection and interoperability.
This document is applicable to the development, design and production of the interconnection and interoperability system of non-woven equipment such as network and fixed network, as well as the construction and transformation of intelligent factories of non-woven production enterprises.
2 Normative references
For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 3100 SI units and recommendations for the use of their multiples and of certain other units
GB/T 33863.3-2017 OPC unified architecture - Part 3: Address space model
GB/T 33863.5-2017 OPC unified architecture - Part 5: Information model
GB/T 36324-2018 Information security technology - Information security classification specifications of industrial control systems
GB/T 43018.1-2023 Interconnection and interoperation for textile equipment - Part 1：General technology requirements
FZ/T 90111-2016 Textile machinery terminology - Spunlaid nonwoven machinery
3 Terms and definitions
The terms and definitions defined in GB/T 43018.1, FZ/T 90111-2016 and the following are applicable to this document.
3.1
carding web forming
method of forming fiber web through fiber opening and carding processes similar to traditional textile pre-spinning techniques
3.2
airlaid
method of forming fiber web through fiber opening and carding processes similar to traditional textile pre-spinning techniques
3.3
wetlaid
method using water as medium to suspend short fibers uniformly, depositing them on permeable conveyor belts or perforated drums to form wet fiber webs
3.4
spunlaid
method using polymers like PP, PET, PLA, PE, PA to form fiber webs by directly laying melt-spun filament bundles onto conveyor nets
4 Abbreviations
The following abbreviations apply to this document.
DCS: Distributed Control System
HTTP: Hyper Text Transfer Protocol
IPC: Industrial Personal Computer
OPC UA: Open Platform Communication Unified Architecture
PLC: Programmable Logic Controller
SCADA: Supervisory Control and Data Acquisition
TCP: Transmission Control Protocol
5 Architecture
5.1 System architecture
The interconnection and interoperability system architecture of nonwoven equipment is shown in Figure 1. It consists of equipment layer, control layer and production management layer, which realizes information exchange from the bottom equipment layer to the management layer, and monitors the production status and equipment information on site in real time.
5.2 Information exchange
It shall comply with the requirements of 5.2 in GB/T 43018.1-2023.
6 Basic requirements
6.1 Device interface and protocol
6.1.1 Device Interface
Equipment interface requirements for interconnection and interoperability of nonwoven equipment:
a) It should support high-speed data transmission to meet real-time requirements;
b) It should have anti-interference and stability to ensure the reliability of data transmission;
c) It should have security functions to protect the security and integrity of equipment and data;
d) It should be compatible with existing network infrastructure and be able to seamlessly connect and communicate with other devices;
e) Should be scalable; Extension interfaces should be left at each level or section;
f) Nonwoven equipment can adopt network type interfaces such as fieldbus, industrial Ethernet, and wireless communication network; The network interface of the device should be consistent with the network interface of the server. If not, the device should be connected to the server through the gateway.
6.1.2 Communication protocol
It shall comply with the requirements of 6.1 in GB/T 43018.1-2023.
6.2 Network
Network requirements for interconnection and interoperability of nonwoven equipment:
a) High-speed data transmission should be supported to ensure real-time and efficient performance;
b) It should have anti-interference capabilities and high reliability to ensure continuous data transmission and communication;
c) It should have security functions to protect the security and integrity of data;
d) It should be flexible and scalable, be able to adapt to different production environments, support the addition and upgrade of new and old equipment, and meet changing needs;
e) The nonwoven factory network can be divided into two channels: production equipment and production execution terminals to ensure complete equipment functions and safe cross-regional operation of equipment;
f) A safety gate should be set between the production equipment and its supporting control system and the superior management system network to be isolated from the production execution terminal network equipment; The gate should be an industrial grade product, suitable for non-woven factory environment.
