1 Scope
This part specifies test methods on such aspects as function, performance, service, environment, reliability, battery and charger for 2GHz WCDMA digital cellular mobile communication network user equipment (UE) (Phase III).
This part is applicable to WCDMA modules of various types of single-mode UE, double-mode UE and multi-mode UE of 2GHz WCDMA digital cellular mobile communication network (Phase III).
2 Normative References
The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections), or revisions, of any of these publications do not apply to this standard. However parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 18287 General Specification of Lithium-ion Battery for Cellular Phone
GB/T 18288-2000 General Specification of Nickel-metal Hydride Battery for Cellular Phone
GB/T 18289-2000 General Specification of Nickel-cadmium Battery for Cellular Phone
GB 4943-2001 Safety of Information Technology Equipment
YD 1268.1-2003 The Safety Specification and Test Method for Lithium Batteries and Charger
YD 1268.2-2003 The Safety Specification and Test Method for Lithium Batteries and Charger
YD/T 1491-2006 Testing Requirement for Mobile Termination Supporting J2ME
YD/T 1493-2006 Testing Methods of WAP Terminal in Digital Cellular Mobile Telecommunication Network
YD/T 1497-2006 Digital Cellular Mobile Telecommunication Network Service Testing Specification for Mobile Streaming Terminal
YD/T 1502-2006 Digital Cellular Mobile Telecommunication Network Testing Specification for Multimedia Message Service Terminal Equipment
YD/T 1538-2006 Technical Requirements and Testing Methods for Acoustics Performance of Digital Mobile Terminal
YD/T 1539-2006 Technical Requirements and Testing Methods for Reliability of Mobile Telecommunication Handset
YD/T 1591 Technical Requirements and Test Method of Charger and Interface for Mobile Telecommunication Terminal Equipment
YD/T 1595.1-2007 Requirements and Measurement Methods of Electromagnetic Compatibility for 2GHz WCDMA Digital Cellular Mobile Communication System - Part 1: User Equipment and Ancillary Equipment - Part 1: User Equipment and Ancillary Equipment
YD-T 1644.1-2007 Human Exposure to Radio Frequency Fields from Hand-held and Body-mounted Wireless Communication Devices - Human Models, Instrumentation, and Procedures - Part 1: Procedure to Determine the Specific Absorption Rate (SAR) for Hand-held Devices in Close Proximity to the Ear (Frequency Range of 300MHz~3GHz)
3 Abbreviations and Symbols
3.1 Abbreviations
For the purposes of this standard, the following abbreviations apply.
... ...
... ...
3.2 Symbols
For the purposes of this standard, the following symbols apply:
DPCH_Ec Average energy per Pseudo Noise chip for Dedicated Physical Channel
Ec Average energy per Pseudo Noise chip
Fuw Frequency of unwanted signal
INode_B Interference signal power level at base station
Io Total receiving power spectral density at the user equipment antenna interface
Ioac Adjacent frequency channel power spectral density at the user equipment antenna interface
Ioc Band-limited white noise power spectral density at the user equipment antenna interface
Îor Power spectral density received by the downlink at the user equipment antenna interface
Ior Total power spectral density of downlink signal at the base station antenna interface
Iouw Interference signal power level at the user equipment antenna interface
R Quantity of information bits (including CRC bits) successfully received by the UE with HSDPA function on HS-DSCH per second
4 Test Environment
Normal test environment refers to the combination of various conditions specified below, all tests other than environmental adaptability test shall be carried out in normal test environment. The reference test environment for RF test is shown in Figure 1. The network test environment for functional test is shown in Figure 2. It is a real WCDMA network or an simulation network with the same structure, including a complete WCDMA radio access network subsystem and core network subsystem.
Foreword i
1 Scope
2 Normative References
3 Abbreviations and Symbols
4 Test Environment
5 Service
6 Basic Functions of UE
7 RF Performance
8 Audio Frequency
9 Environment and Reliability
10 Requirements and Measurement Method for Standby Time and Talk Time of Mobile Station
11 Electromagnetic Compatibility
12 Test of Specific Absorption Rate (SAR)
13 Test of Battery Charger
14 Appearance, Packaging and Assembly
