标准编号:	GB/T 819.1-2016
中文名称:	十字槽沉头螺钉 第1部分：4.8级
英文名称:	Countersunk flat head screws with cross recess―Part 1: Property class 4.8
中标分类:	J13    紧固件
行业分类:	GB    国家标准
ICS分类:	21.060.10 21.060.10    螺栓、螺钉、螺柱 21.060.10
发布机构:	中华人民共和国国家质量监督检验检疫总局 中国国家标准化管理委员会
发布日期:	2016-02-24
实施日期:	2016-6-1
标准状态:	valid
替代旧标准:	GB/T 819.1-2000 十字槽沉头螺钉 第1部分：钢4.8级
翻译语言:	英文
文件格式:	PDF
中文字符数:	7000 字
翻译价格(元):	290.0
交付时间:	付款后 1 个工作日

1 Scope This part of GB/T 819 specifies the type dimensions, requirements and designation of countersunk flat head screws with cross recess and property class 4.8. This part is applicable to countersunk flat head screws with type H or Z cross recess and with thread of M1.6~M10, property class of 4.8 and product grade of A. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the normative document (including any amendments) applies. GB/T 90.1 Fasteners - Acceptance Inspection (GB/T 90.1-2002, ISO 3269:2000, IDT) GB/T 90.2 Fasteners - Marking and Packaging GB/T 193 General Purpose Metric Screw Threads - General Plan (GB/T 193-2003, ISO 261:1998, MOD) GB/T 944.1 Cross Recesses for Screws (GB/T 944.1-1985, eqv ISO 4757:1983) GB/T 1237 Designation System for Fasteners (GB/T 1237-2000, eqv ISO 8991:1986) GB/T 3098.1 Mechanical Properties of Fasteners - Bolts, Screws and Studs (GB/T 3098.1-2010, ISO 898-1:2009, MOD) GB/T 3103.1 Tolerances for Fasteners - Bolts, Screws, Studs and Nuts (GB/T 3103.1-2002, idt ISO 4759-1: 2000) GB/T 5267.1 Fasteners - Electroplated Coatings (GB/T 5267.1-2002, ISO 4042:1999, IDT) GB/T 5276 Fasteners; Bolts, Screws, Studs and Nuts; Symbols and Designations of Dimensions (GB/T 5276-2015, ISO 225:2010, MOD) GB/T 5279 Countersunk Head Screws - Head Configuration and Gauging (GB/T 5279-1985, idt ISO 7721:1983) GB/T 5279.2 Countersunk Flat Head Screws - Part 2: Penetration Depth of Cross Recesses (GB/T 5279.2-1997, idt ISO 7721-2:1990) GB/T 5779.1 Fasteners - Surface Discontinuities - Bolts, Screws and Studs for General Requirements (GB/T 5779.1-2000, idt ISO 6157-1:1988) GB/T 9145 General Purpose Metric Screw Threads - Limits of Sizes for the Screw Threads of Medium Quality and Preferable Plan (GB/T 9145-2003, ISO 965-2:1998, MOD) GB/T 16938 Fasteners - General Requirements for Blots, Screws, Studs and Nuts (GB/T 16938-2008, ISO 8992:2005, IDT) 3 Dimensions See Figure 1 and Table 1. Symbols and descriptions of dimensions shall meet those specified in GB/T 5276.

4 Requirements and Reference Standards 5 Designation