This standard describes the planning, design as well as setting principles and requirements of a safety way guidance system (SWGS) in public building.
This standard is not only applicable to design and arrangement of electric light source element and phosphorescent light element of SWGS in public building but also applicable to the situation that different SWGS elements are determined according to SWGS service environment, materials, design, installation and maintenance.
This standard also does not include the special considerations of possible tactile or audible emergency facilities of SWGS, nor does it include requirements concerning the emergency escape route lighting, especially the design and application of emergency escape route lighting, unless illumination is used to mark safety equipment or special features of the escape route like the emergency exit doors or stairs.
This standard is not applicable to SWGS design and arrangement of ships through waterway and sea transportation.
Foreword I
Introduction II
1 Scope 1
2 Normative References 1
3 Terms and Definitions 2
4 Planning a Safety Way Guidance System (SWGS) 2
4.1 General 2
4.2 Selection of Components 3
5 Basic Principles for the Design of SWGS 3
5.1 Design Objectives 3
5.2 Consistent and Unambiguous Use of Safety Direction Sign 5
5.3 Principles of Design using the Different Visual Components 6
6 Specific Requirements for Electrically Powered Components 9
6.1 General 9
6.2 Requirements for Safety Direction Lines and High-located Safety Direction Signs 9
6.3 Marking 11
6.4 Fire-fighting, Emergency and Safety Equipment 11
6.5 Emergency Power Supply and Operating Conditions for the Electrically Powered Components 12
6.6 Documentation and Logbook 12
6.7 Inspection and Maintenance 12
7 Specific Requirements for Phosphorescent Components 12
7.1 General 12
7.2 Phosphorescent Components and Their Location Within a SWGS 12
7.3 Luminance Requirements for Phosphorescent Components of a SWGS 14
7.4 Width of Low Location Safety Direction Line 15
7.5 Illumination Requirements 15
7.6 Verification of Illumination and Luminance 15
7.7 Documentation and Logbook 16
7.8 Inspection and Maintenance 16
Appendix A (Informative) Examples of SWGS Layouts 17
Appendix B (Informative) Measurement of Photopic Luminance of Phosphorescent Components in the Laboratory 35
Appendix C (Informative) On-site Measurement of Luminance Performance of Phosphorescent Components 40
References 43
Figure 1 Examples of Safety Direction Signs Arranged Aboveground 6
Figure A.1 Example Layout of a T-junction Leading into a Straight Corridor no Wider than 2m and no Longer than 10m 18
Figure A.2 Example Layout of a T-junction Leading into a Straight Corridor no Wider than 2m with Illumination to Highlight the Door and the T-junction 18
Figure A.3 Example Layout of a Corridor Wider than 2m with Low Mounted Safety Direction Line on Both Sides 19
Figure A.4 Example Layout of a T-Junction Leading into a Straight Corridor Wider than 2m with an Adjoining Door (Demarked by a Floor Guide Line) 20
Figure A.5 Example Layout of a T-junction Leading into a Straight Corridor Wider than 2m with Focused Illumination on T-junction and Door 21
Figure A.6 Example Layout of a T-junction Wider than 2m with Door (with Safety Direction Sign) Using Floor Guide Lines 22
Figure A.7 Example Layout of a T-junction Leading into a Straight Corridor (with More than One Door) Showing Continuity of Signing 23
Figure A.8 Example Layout of a T-junction Leading into a Straight Corridor Less than 2m with Focused Illumination at the Doors, Provided by High-Mounted Single-Sided Trans-illuminated Safety Direction Signs 23
Figure A.9 Example Layout of a Building Feature Marking and Safety Direction Signs Through Doors 24
Figure A.10 Example Layout of an Alternative Building Feature Marking and Full Frame Door Marking 24
Figure A.11 Example Layout of Safety Direction Sign for a Dead End Corridor no Wider than 2m 25
Figure A.12 Example Layout of an Intersection Marked by Floor Safety Direction Lines 26
Figure A.13 Example Layout of an Intersection Illustrating Floor Safety Direction Lines with Safety Direction Sign 26
Figure A.14 Example Layout of an Intersection with a Wall-Mounted Safety Direction Line 27
Figure A.15 Example Layout of an Open Space Illustrating Floor Safety Direction Line with Safety Direction Sign 28
Figure A.16 Example Layout of an Open Space with intersection and Floor Safety Direction Line with Intersection 29
Figure A.17 Example Layout of a Collection of Different Marking of Stairs and Handrails 30
Figure A.18 Example Layout of Stairs Where the Stair Treads are Illuminated with Illuminant Sources 31
Figure A.19 Example Layout of Stairs Where the Treads are Illuminated by Low Mounted Illuminant Sources on the Wall 32
Figure A.20 Example Layout of Safety Direction Sign of Slope (Change of Level) 33
Figure A.21 Example Layout of Safety Direction Sign of Ramp (Change of Level) 34
Table 1 Examples of Safety Direction Signs to be Used with or without Auxiliary Words 5
Table 2 Minimum Requirements for The Luminance Decay Properties 14
Table 3 Minimum Requirements for Luminance of Installed Components 15
