GB 43473-2023 Controlgear and other auxiliaries for electric lighting products - Safety requirements
1 Scope
This document specifies the safety requirements of the marking, mechanical structure and electrical structure of controlgear and other auxiliaries for electric lighting products, and describes the corresponding verification methods.
This document is applicable to controlgear for light sources and their components for use on d.c. or a.c. supplies up to 1 000V (a.c. at 50Hz or 60Hz).
Note: The term "light source" in this document refers exclusively to "electric light source".
2 Normative references
The following documents contain provisions which, through reference in this text, constitute provisions of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 19510.1 Controlgear for electric light sources - Part 1: General and safety requirements
GB/T 19510.201 Controlgear for light sources - Part 2-1: Particular requirements for starting devices (other than glow starters)
GB/T 19510.202 Controlgear for electric light sources - Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps
GB/T 19510.203 Controlgear for electric light sources - Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps
GB/T 19510.207 Controlgear for electric light sources - Part 2-7: Particular requirements for electric source for safety services (ESSS) supplied electronic controlgear for emergency lighting (self-contained)
GB/T 19510.208 Controlgear for electric light sources - Part 2-8: Particular requirements for ballasts for fluorescent lamps
GB/T 19510.209 Controlgear for electric light sources - Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps)
GB 19510.210 Lamp controlgear - Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes)
GB/T 19510.211 Controlgear for electric light sources - Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires
GB/T 19510.212 Controlgear for electric light sources - Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)
GB/T 19510.213 Controlgear for electric light sources - Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 19510.1, GB/T 19510.201~203, GB/T 19510.207~209, GB 19510.210 and GB/T 19510.211~213 as well as the following apply.
3.1
controlgear for light sources
unit between the supply and one or more light sources to provide rated voltage or current to the light source
Note 1: The controlgear for light sources consists of one or more independent components.
Note 2: The controlgear for light sources have one or more control functions such as triggering, dimming, power factor correction and radio interference suppression.
Note 3: The controlgear for light sources consists of a power supply unit and/or a control unit.
Note 4: The controlgear for light sources is partially or fully integrated in the light source.
3.1.1
built-in controlgear for light sources
controlgear for light sources designed to be built into a luminaire, a box, an enclosure or the like
Note: The controlgear compartment in the base of a road lighting column is considered to be an enclosure.
3.1.2
independent controlgear for light sources
controlgear for light sources consisting of one or more components so designed that it can be mounted separately outside a luminaire, with protection according to the marking of the controlgear for light sources and without any additional enclosure
Note: This may consist of a built-in controlgear for light sources housed in a suitable enclosure which provides all the necessary protection according to its markings.
3.1.3
integral controlgear for light sources
Foreword i
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Requirements
6 Verification methods
Annex A (Normative) Compliance verification standards
