Foreword
Codeofchina.com is in charge of this English translation. In case of any doubt about the English translation, the Chinese original shall be considered authoritative.
This standard is developed in accordance with the rules given in GB/T 1.1-2009.
This standard was proposed by the China Building Materials Federation.
This standard is under the joint jurisdiction of the National Technical Committee on Glass in Building of Standardization Administration of China (SAC/TC 255) and the National Technical Committee on Energy Fundamentals and Management of Standardization Administration of China (SAC/TC 20).
Test method of energy consumption per unit products for tempered glass
1 Scope
This standard specifies the statistical classification, statistical period and statistical preparation of energy consumption per unit products for tempered glass, as well as the energy consumption statistics, output statistics and energy consumption calculation methods of energy consumption per unit products for tempered glass.
This standard is applicable to the energy consumption test of flat tempered glass production line using physical tempering method.
This standard is not applicable to the energy consumption test of tempered glass production line using chemical method.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB 15763.2 Safety glazing materials in building - Part 2: Tempered glass
GB/T 20840.2 Instrument transformers - Part 2: Additional requirements for current transformers
3 Statistical classification
Statistics of common flat tempered glass, low emissivity coated flat tempered glass, common curved tempered glass and low emissivity coated curved tempered glass shall be measured separately.
4 Statistical period
The statistical period of one tempered glass production line producing glass with the same thickness and category is at least 1 hour of continuous production and no less than 5 furnace volumes.
Foreword i
1 Scope
2 Normative references
3 Statistical classification
4 Statistical period
5 Statistical preparation
6 Energy consumption and output statistics
7 Calculation method of energy consumption
ICS 81.040.20
Q 33
GB
中华人民共和国国家标准
GB/T 36267—2018
钢化玻璃单位产品能耗测试方法
Test method of energy consumption per unit products for tempered glass
2018-06-07发布 2019-05-01实施
国家市场监督管理总局
中国国家标准化管理委员会 发布
前言
本标准按照GB/T 1.1—2009给出的规则起草。
本标准由中国建筑材料联合会提出。
本标准由全国建筑用玻璃标准化技术委员会(SAC/TC 255)、全国能源基础与管理标准化技术委员会(SAC/TC 20)共同归口。
钢化玻璃单位产品能耗测试方法
1 范围
本标准规定了钢化玻璃单位产品能耗的统计分类、统计期、统计准备、能耗及产量统计和能耗计算方法。
本标准适用于物理钢化法水平式钢化玻璃生产线能耗的测试。
本标准不适用于化学法钢化玻璃生产线能耗的测试。
2 规范性引用文件
下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件，仅注日期的版本适用于本文件。凡是不注日期的引用文件，其最新版本(包括所有的修改单)适用于本文件。
GB 15763.2 建筑用安全玻璃 第2部分：钢化玻璃
GB/T 20840.2 互感器第2部分：电流互感器的补充技术要求
3 统计分类
平面普通钢化玻璃、平面低辐射镀膜钢化玻璃、曲面普通钢化玻璃和曲面低辐射镀膜钢化玻璃分别统计。
4 统计期
同一钢化玻璃生产线同厚度同类别钢化玻璃统计期为：至少连续生产1h，且不少于5炉。
