1 Scope
This standard specifies terms and definitions, product classification and designation, technical requirements, test methods and inspection rules of non-directional self-ballasted LED-lamps for general lighting service.
This standard is applicable to non-directional self-ballasted LED-lamps, integrating all elements for stable operation, for domestic and similar general lighting purposes.
The range of application is as follows:
— a rated wattage up to 60 W;
— a rated voltage (AC) of up to 250V, 50Hz;
— a screw lamp cap according to GB/T 1406.1 or a bayonet lamp cap according to GB/T 1406.5.
Note: Unless otherwise specified, "lamp" in this standard represents "non-directional self-ballasted LED-lamps for general lighting service".
Lamps which comply with this standard shall start and operate satisfactorily at voltages between 92% and 106% of rated supply voltage and at an ambient air temperature of between -20℃ and 45℃.
2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 1406.1 Types and Dimensions of Lamp Caps — Part 1: Screw Caps
GB/T 1406.5 Types and Dimensions of Lamp Caps — Part 5: Bayonet Caps
GB/T 1483.1 Gauges for Lamp Caps and Holders — Part 1: Gauges for Screw Caps and Holders
GB/T 1483.5 Gauges for Caps and Lampholders — Part 5: Gauges for Bayonet Caps and Lampholders
GB/T 2828.1 Sampling Procedures for Inspection by Attributes — Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-Lot Inspection
GB/T 2829 Sampling Procedures and Tables for Periodic Inspection by Attributes ( Apply to Inspection of Process Stability)
GB/T 7249 Maximum Lamp Outlines for Incandescent Lamps
GB/T 10681 Tungsten Filament Lamps for Domestic and Similar General Lighting Purposes — Performance Requirements
GB 17625.1 Electromagnetic Compatibility — Limits — Limits for Harmonic Current Emissions (Equipment Input Current ≤ 16 A Per Phase)
GB 17743 Limits and Methods of Measurement of Radio Disturbance Characteristics of Electrical Lighting and Similar Equipment
GB/T 18595 Equipment for General Lighting Purposes — EMC Immunity Requirements
GB/T 20145 Photobiological Safety of Lamps and Lamp Systems
GB/T 24824 Measurement Methods of LED Modules for General Lighting
GB/T 24826 General Lighting — Light Emitting Diode (LED) Products and Related Equipment — Terms and Definitions
GB 24906 Self-ballasted LED Lamps for General Lighting Services >50 V — Safety Specifications
GB/T 31112 Classification of Non-directional Self-ballasted LED-lamps for General Lighting Services
3 Terms and Definitions
For the purpose of this document, the terms and definitions given in GB/T 24826 and GB/T 31112 and the following apply.
3.1 self-ballasted LED lamp
unit which cannot be dismantled without being permanently damaged, provided with a lamp cap and incorporating a LED light source and any additional elements necessary for starting and stable operation of the light source
3.2 directional lighting
lamp with more than 80% light output at a solid angle of π sr (equivalent to solid angle of 120° of taper conical angle)
3.3 non-directional lighting
lamp with less than 80% light output at a solid angle of π sr (equivalent to solid angle of 120° of taper conical angle)
3.4 non-directional self-ballasted LED lamp
self-ballasted LED-lamps with the characteristics of non-directional lighting lamps
3.5 Initial value
Photometric and color parameters at the end of the ageing period of 1000h
3.6 power factor
the ratio between measured active power of lamp to the product of input voltage (r.m.s) and input current (r.m.s)
3.7 early failure
failures of lamp, such as no light-emitting, obvious flicker or luminous flux reduction in the ageing period of 1000h
3.8 average life(life to 50% failures)
length of time during which a complete LED-lamp no longer provides 50% (or 70%) of the rated luminous flux, under standard test conditions
3.9 lumen maintenance
Luminous flux at a given time in the life of a LED-lamp divided by the initial value of the luminous flux of the lamp and expressed as a percentage of the initial luminous flux
Foreword I
1 Scope
2 Normative References
3 Terms and Definitions
4 Product Classification and Designation
5 Technical Requirements
6 Test Method
7 Inspection Rules
