This standard is applicable to the single sawblade circular saw bench (with or without travelling table) and the circular sawing machine with travelling table (dimension saw) (hereinafter referred to as "machines"). They are designed to cut solid wood, chipboard, fiberboard, plywood and also these materials where they are covered with plastics edging and/or plastics (light alloy) laminates.
This standard is applicable to the machine manufactured after the implementation date of this standard.
This standard is not applicable to the hand-rocking universal circular saw bench; table-top circular saw bench and hand-held circular saw bench.
This standard specifies the safety technical requirements and inspection methods of the machine.
Foreword III
1 Scope
2 Normative References
3 Terms and Definitions
4 List of Hazards
5 Safety Requirements and/or Measures
5.1 Control and Command Devices
5.1.1 Safety and Reliability of Control System
5.1.2 Position of Controls
5.1.3 Starting
5.1.4 Normal Stopping
5.1.5 Emergency Stop
5.1.6 Mode Selection
5.1.7 Speed Changing
5.1.8 Failure of the Power Supply
5.1.9 Failure of Control Circuits
5.1.10 Power Operated Movement of the Sawblade and/or Fence
5.2 Protection Against Mechanical Hazards
5.2.1 Stability
5.2.2 Risk of Break-up during Operation
5.2.3 Tool Holder and Tool Design
5.2.4 Braking
5.2.4.1 General
5.2.4.2 Test Conditions
5.2.4.3 Tests
5.2.5 Devices to Minimize the Possibility of Ejection
5.2.6 Workpiece Supports and Guides
5.2.6.1 Workpiece Guides and Fences
5.2.6.2 Table Size
5.2.6.3 Extension Tables
5.2.6.4 Travelling Table
5.2.7 Prevention of Access to Moving Parts
5.2.7.1 Guarding of the Tools
5.2.7.2 Guarding of Drives
5.2.8 Clamping Devices
5.2.9 Safety Appliance (Work Device with Protecting Function)
5.3 Protection against Non-mechanical Hazards
5.3.1 Fire and Explosion
5.3.2 Noise
5.3.2.1 Noise Reduction at the Design Stage
5.3.2.2 Noise Measurement
5.3.2.3 Noise Declaration
5.3.3 Emission of Chips, Dust and Harmful Gases
5.3.4 Electrical Equipment
5.3.5 Requirements for Ergonomics and Safe Handling
5.3.6 Lighting
5.3.7 Pneumatic
5.3.8 Hydraulic device
5.3.9 Heat
5.3.10 Hazardous Materials
5.3.11 Vibration
5.3.12 Laser
5.3.13 Static electricity
5.3.14 Errors of fitting
5.3.15 Isolation of energy transfer
5.3.16 Maintenance
6 Information for Use
6.1 Warning Devices
6.2 Marking
6.2.1 Marking of Riving Knives
6.2.2 Marking of the Machine
6.3 Instruction Handbook
Appendix A (Normative) Test for Rigidity of Building Site Saws
Appendix B (Normative) Test of Geometric Accuracy of Saw Spindle
Appendix C (Normative) Riving Knife Mounting Strength Test
C.1 Strength Test of the Riving Knife
Appendix D (Normative) Riving Knife Lateral Stability Test
D.1 Test Requirement
Appendix E (Normative) Machine Table and Insert Minimum Dimensions
Appendix F (Normative) Test for Stability of Sawblade Guard
F.1 Sawblade Guard Mounted Separately from Riving Knife
F.2 Sawblade Guard Mounted on the Riving Knife
Appendix G (Normative) Operating Conditions of Machine During Noise Measurement
G.1 General
G.2 Noise Measurement
G.3 Data Sheet for Noise Measurement of the Machine
Appendix H (Informative) Safe Working Practice
H.1 Use of Push Block and Push Stick
H.2 Selection of Sawblade and Riving Knife
H.3 Selection of riving knife
H.4 Fixing of Sawblade to Spindle
H.5 Lighting
