1 Scope
This part specifies general and safety requirements for lamp controlgear for use on d.c. supplies up to 250 V and/or a.c. supplies up to 1,000 V at 50 Hz or 60 Hz.
This part also covers lamp controlgear for lamps which are not yet standardized.
Tests dealt with in this part are type tests. Requirements for testing individual lamp controlgear during production are not included in this part.
Requirements for semi-luminaires are given in GB 7000 (see 1.2.60 in GB 7000.1-2007).
In addition to the requirements given in this part, Appendix B sets out general and safety requirements applicable to thermally protected lamp controlgear.
Appendix C sets out additional general and safety requirements as they apply to electronic lamp controlgear with means of protection against overheating.
Additional requirements for built-in ballasts with double or reinforced insulation are given in Appendix I.
2 Normative References
The following standards contain provisions which, through reference in this part of GB 19510, constitute provisions of this part. For dated reference, subsequent amendments to (excluding corrections to), or revisions of, any of these publications do not apply. However, the parties to agreements on this part are encouraged to investigate the possibility of applying the most recent editions of the standards. For undated references, the latest edition of the normative document referred to applies.
Fire Hazard Testing for Electric and Electronic Products-Part 5: Test Flames-Needle Test Method-Apparatus Confirmatory Arrangement and Guidance (GB/T 5169.5-2008 IEC 60695-11-5: 2004, IDT)
GB/T 5169.10 Fire Hazard Testing for Electric and Electronic Products - Part 10: Glow/Hot-wire Based Test Methods-Glow-wire Apparatus and Common Test Procedure (GB/T 5169.10-2006, IEC 60695-2-10: 2000, IDT)
GB/T 5465.2-2008 Graphical Symbols for Use on Electrical Equipment - Part 2: Graphical Symbols(IEC 60417 DB: 2007, IDT)
GB 7000.1 – 2007 Luminaires - Part 1: General Requirements and Tests(IEC 60598-1: 2003, IDT)
GB/T 12113-2003 Methods of Measurement of Touch Current and Protective Conductor Current(IEC 60990: 1999, IDT)
GB 14536.4 Automatic Electrical Controls for Household and Similar Use - Particular Requirements for Thermal Protectors for Ballasts for Tubular Fluorescent Lamps(GB 14536.4-2008, IEC 60730-2-3: 2006, IDT)
GB/T 15144-2009 A.C. Supplied Electronic Ballasts for Tubular Fluorescent Lamps - Performance Requirements(IEC 60929: 2006, IDT)
GB/T 16935.3 Insulation Coordination for Equipment within Low-voltage Systems - Part 3: Use of Coating，Potting or Moulding for Protection Against Pollution(GB/T 16935.3-2005, IEC 60664-3: 2003, IDT)
GB 19510.2~
GB l9510.14 Lamp Controlgear - Part 2 ~ Part 14: Particular Requirements (IEC 61347-2 (all parts), IDT)
GB 19510.9 Lamp Controlgear-Part 9: Particular Requirements for Ballasts for Fluorescent Lamps (GB 19510.9-2009, IEC 6 1347-2-8: 2006, IDT)
GB 19510.10-2009 Lamp Controlgear-Part 10: Particular Requirements for Ballasts for Discharge Lamps (Excluding Fluorescent Lamps)(IEC 61347-2-9: 2003, IDT)
Foreword I
Introduction IV
1 Scope
2 Normative References
3 Terminologies and Definitions
4 General Requirements
5 General Notes on Tests
6 Classification
7 Marking
8 Terminals
9 Provisions for Protective Earthing
10 Protection against Accidental Contact with Live Parts
11 Moisture Resistance and Insulation
12 Electric Strength
13 Thermal Endurance Test for Windings of Ballasts
14 Fault Conditions
15 Construction
16 Creepage Distances and Clearances
17 Screws, Current-carrying Parts and Connections
18 Resistance to Heat, Fire and Tracking
19 Resistance to Corrosion
20 No-load Output Voltage
Appendix A (Normative) Test to Establish Whether a Conductive Part Is a Live Part Which May Cause an Electric Shock
Appendix B (Normative) Particular Requirements for Thermally Protected Lamp Controlgear
Appendix C (Normative) Particular Requirements for Electronic Lamp Controlgear with Means of Protection against Overheating
Appendix D (Normative) Requirements for Carrying out the Heating Tests of Thermally Protected Lamp Controlgear
Appendix E (Normative) Use of Constant S Other Than 4,500 in tw (Winding Temperature) Tests
Appendix F (Normative) Draught-proof Enclosure
Appendix G (Normative) Explanation of the Derivation of the Values of Pulse Voltages
Appendix H (Normative) Tests
Appendix I (Normative) Additional Requirements for Built-in Magnetic Ballasts with Double or Reinforced Insulation
Appendix J (Normative) Schedule of More Onerous Requirements
Appendix K (Informative) Conformity Testing during Manufacture
Bibliography
